Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
/*-
|
2006-01-05 21:27:19 +00:00
|
|
|
|
* Copyright (c) 1998 - 2006 S<EFBFBD>ren Schmidt <sos@FreeBSD.org>
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
* All rights reserved.
|
|
|
|
|
*
|
|
|
|
|
* Redistribution and use in source and binary forms, with or without
|
|
|
|
|
* modification, are permitted provided that the following conditions
|
|
|
|
|
* are met:
|
|
|
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
|
|
|
* notice, this list of conditions and the following disclaimer,
|
|
|
|
|
* without modification, immediately at the beginning of the file.
|
|
|
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
|
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
|
|
|
* documentation and/or other materials provided with the distribution.
|
|
|
|
|
*
|
|
|
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
|
|
|
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
|
|
|
|
|
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
|
|
|
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
|
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
|
|
|
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
|
|
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
|
|
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
|
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
|
|
|
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
|
*/
|
|
|
|
|
|
2003-08-24 17:55:58 +00:00
|
|
|
|
#include <sys/cdefs.h>
|
|
|
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
|
|
1999-10-09 19:57:13 +00:00
|
|
|
|
#include "opt_ata.h"
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <sys/param.h>
|
|
|
|
|
#include <sys/systm.h>
|
2001-03-15 15:36:25 +00:00
|
|
|
|
#include <sys/ata.h>
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <sys/kernel.h>
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
#include <sys/module.h>
|
2003-08-24 09:22:26 +00:00
|
|
|
|
#include <sys/endian.h>
|
2003-10-10 11:00:06 +00:00
|
|
|
|
#include <sys/ctype.h>
|
2001-03-15 15:36:25 +00:00
|
|
|
|
#include <sys/conf.h>
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#include <sys/bus.h>
|
2000-05-05 09:59:14 +00:00
|
|
|
|
#include <sys/bio.h>
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <sys/malloc.h>
|
2000-01-27 19:00:51 +00:00
|
|
|
|
#include <sys/sysctl.h>
|
2004-01-14 21:26:35 +00:00
|
|
|
|
#include <sys/sema.h>
|
2003-08-24 09:22:26 +00:00
|
|
|
|
#include <sys/taskqueue.h>
|
2004-01-14 21:26:35 +00:00
|
|
|
|
#include <vm/uma.h>
|
2000-01-24 20:45:24 +00:00
|
|
|
|
#include <machine/stdarg.h>
|
1999-04-18 20:48:15 +00:00
|
|
|
|
#include <machine/resource.h>
|
|
|
|
|
#include <machine/bus.h>
|
|
|
|
|
#include <sys/rman.h>
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
#include <dev/ata/ata-all.h>
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
#include <ata_if.h>
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* device structure */
|
|
|
|
|
static d_ioctl_t ata_ioctl;
|
2004-05-20 14:49:12 +00:00
|
|
|
|
static struct cdevsw ata_cdevsw = {
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
.d_version = D_VERSION,
|
2005-04-21 11:13:39 +00:00
|
|
|
|
.d_flags = D_NEEDGIANT, /* we need this as newbus isn't mpsafe */
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
.d_ioctl = ata_ioctl,
|
|
|
|
|
.d_name = "ata",
|
2001-03-15 15:36:25 +00:00
|
|
|
|
};
|
|
|
|
|
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
/* prototypes */
|
2000-02-18 20:57:33 +00:00
|
|
|
|
static void ata_boot_attach(void);
|
2005-04-29 11:30:03 +00:00
|
|
|
|
static device_t ata_add_child(device_t, struct ata_device *, int);
|
2005-11-25 09:00:56 +00:00
|
|
|
|
static int ata_getparam(struct ata_device *, int);
|
2005-04-29 11:30:03 +00:00
|
|
|
|
static void bswap(int8_t *, int);
|
|
|
|
|
static void btrim(int8_t *, int);
|
|
|
|
|
static void bpack(int8_t *, int8_t *, int);
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
2003-11-11 14:55:36 +00:00
|
|
|
|
/* global vars */
|
2005-10-31 15:41:29 +00:00
|
|
|
|
MALLOC_DEFINE(M_ATA, "ata_generic", "ATA driver generic layer");
|
2005-05-16 13:07:27 +00:00
|
|
|
|
int (*ata_raid_ioctl_func)(u_long cmd, caddr_t data) = NULL;
|
2006-03-08 16:39:01 +00:00
|
|
|
|
struct intr_config_hook *ata_delayed_attach = NULL;
|
2003-11-11 14:55:36 +00:00
|
|
|
|
devclass_t ata_devclass;
|
2005-04-18 16:01:56 +00:00
|
|
|
|
uma_zone_t ata_request_zone;
|
|
|
|
|
uma_zone_t ata_composite_zone;
|
2004-05-20 14:49:12 +00:00
|
|
|
|
int ata_wc = 1;
|
2003-11-11 14:55:36 +00:00
|
|
|
|
|
|
|
|
|
/* local vars */
|
|
|
|
|
static int ata_dma = 1;
|
2004-08-01 12:31:38 +00:00
|
|
|
|
static int atapi_dma = 1;
|
2003-11-11 14:55:36 +00:00
|
|
|
|
|
2001-03-19 08:04:54 +00:00
|
|
|
|
/* sysctl vars */
|
|
|
|
|
SYSCTL_NODE(_hw, OID_AUTO, ata, CTLFLAG_RD, 0, "ATA driver parameters");
|
2003-08-24 09:22:26 +00:00
|
|
|
|
TUNABLE_INT("hw.ata.ata_dma", &ata_dma);
|
2003-11-03 09:25:02 +00:00
|
|
|
|
SYSCTL_INT(_hw_ata, OID_AUTO, ata_dma, CTLFLAG_RDTUN, &ata_dma, 0,
|
|
|
|
|
"ATA disk DMA mode control");
|
2003-08-24 09:22:26 +00:00
|
|
|
|
TUNABLE_INT("hw.ata.atapi_dma", &atapi_dma);
|
2003-11-03 09:25:02 +00:00
|
|
|
|
SYSCTL_INT(_hw_ata, OID_AUTO, atapi_dma, CTLFLAG_RDTUN, &atapi_dma, 0,
|
|
|
|
|
"ATAPI device DMA mode control");
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
TUNABLE_INT("hw.ata.wc", &ata_wc);
|
|
|
|
|
SYSCTL_INT(_hw_ata, OID_AUTO, wc, CTLFLAG_RDTUN, &ata_wc, 0,
|
|
|
|
|
"ATA disk write caching");
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
|
2003-08-24 09:22:26 +00:00
|
|
|
|
/*
|
|
|
|
|
* newbus device interface related functions
|
|
|
|
|
*/
|
2000-09-19 11:08:39 +00:00
|
|
|
|
int
|
2000-02-18 20:57:33 +00:00
|
|
|
|
ata_probe(device_t dev)
|
|
|
|
|
{
|
2004-08-12 08:20:36 +00:00
|
|
|
|
return 0;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
int
|
|
|
|
|
ata_attach(device_t dev)
|
|
|
|
|
{
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
struct ata_channel *ch = device_get_softc(dev);
|
2004-08-12 08:20:36 +00:00
|
|
|
|
int error, rid;
|
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* check that we have a virgin channel to attach */
|
|
|
|
|
if (ch->r_irq)
|
|
|
|
|
return EEXIST;
|
2004-08-12 08:20:36 +00:00
|
|
|
|
|
2000-02-18 20:57:33 +00:00
|
|
|
|
/* initialize the softc basics */
|
2003-08-24 09:22:26 +00:00
|
|
|
|
ch->dev = dev;
|
2004-09-26 11:48:43 +00:00
|
|
|
|
ch->state = ATA_IDLE;
|
|
|
|
|
bzero(&ch->state_mtx, sizeof(struct mtx));
|
|
|
|
|
mtx_init(&ch->state_mtx, "ATA state lock", NULL, MTX_DEF);
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
bzero(&ch->queue_mtx, sizeof(struct mtx));
|
|
|
|
|
mtx_init(&ch->queue_mtx, "ATA queue lock", NULL, MTX_DEF);
|
|
|
|
|
TAILQ_INIT(&ch->ata_queue);
|
2003-03-29 13:37:09 +00:00
|
|
|
|
|
2005-04-08 09:37:47 +00:00
|
|
|
|
/* reset the controller HW, the channel and device(s) */
|
2005-03-31 15:05:40 +00:00
|
|
|
|
while (ATA_LOCKING(dev, ATA_LF_LOCK) != ch->unit)
|
2004-10-06 19:46:08 +00:00
|
|
|
|
tsleep(&error, PRIBIO, "ataatch", 1);
|
2005-04-28 22:08:08 +00:00
|
|
|
|
ATA_RESET(dev);
|
2005-03-31 15:05:40 +00:00
|
|
|
|
ATA_LOCKING(dev, ATA_LF_UNLOCK);
|
2000-02-18 20:57:33 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* setup interrupt delivery */
|
2001-02-06 16:44:25 +00:00
|
|
|
|
rid = ATA_IRQ_RID;
|
2004-03-17 17:50:55 +00:00
|
|
|
|
ch->r_irq = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid,
|
|
|
|
|
RF_SHAREABLE | RF_ACTIVE);
|
Major update of the ATA RAID code, part 1:
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
|
|
|
|
if (!ch->r_irq) {
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
device_printf(dev, "unable to allocate interrupt\n");
|
2000-02-18 20:57:33 +00:00
|
|
|
|
return ENXIO;
|
|
|
|
|
}
|
2003-08-24 09:22:26 +00:00
|
|
|
|
if ((error = bus_setup_intr(dev, ch->r_irq, ATA_INTR_FLAGS,
|
2006-01-18 09:14:55 +00:00
|
|
|
|
(driver_intr_t *)ata_interrupt, ch, &ch->ih))) {
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
device_printf(dev, "unable to setup interrupt\n");
|
2000-02-25 09:48:23 +00:00
|
|
|
|
return error;
|
2002-03-03 15:36:21 +00:00
|
|
|
|
}
|
2000-01-18 21:02:59 +00:00
|
|
|
|
|
2005-04-21 11:13:39 +00:00
|
|
|
|
/* probe and attach devices on this channel unless we are in early boot */
|
|
|
|
|
if (!ata_delayed_attach)
|
|
|
|
|
ata_identify(dev);
|
2000-02-18 20:57:33 +00:00
|
|
|
|
return 0;
|
|
|
|
|
}
|
|
|
|
|
|
2001-03-06 21:43:46 +00:00
|
|
|
|
int
|
2000-02-18 20:57:33 +00:00
|
|
|
|
ata_detach(device_t dev)
|
|
|
|
|
{
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
struct ata_channel *ch = device_get_softc(dev);
|
|
|
|
|
device_t *children;
|
|
|
|
|
int nchildren, i;
|
2004-05-20 14:49:12 +00:00
|
|
|
|
|
2005-09-14 12:45:06 +00:00
|
|
|
|
/* check that we have a valid channel to detach */
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
if (!ch->r_irq)
|
2000-02-18 20:57:33 +00:00
|
|
|
|
return ENXIO;
|
2000-01-18 21:02:59 +00:00
|
|
|
|
|
2006-02-25 17:27:33 +00:00
|
|
|
|
/* grap the channel lock so no new requests gets launched */
|
|
|
|
|
mtx_lock(&ch->state_mtx);
|
|
|
|
|
ch->state |= ATA_STALL_QUEUE;
|
|
|
|
|
mtx_unlock(&ch->state_mtx);
|
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* detach & delete all children */
|
|
|
|
|
if (!device_get_children(dev, &children, &nchildren)) {
|
|
|
|
|
for (i = 0; i < nchildren; i++)
|
|
|
|
|
if (children[i])
|
|
|
|
|
device_delete_child(dev, children[i]);
|
|
|
|
|
free(children, M_TEMP);
|
|
|
|
|
}
|
2004-07-12 10:50:50 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* release resources */
|
Major update of the ATA RAID code, part 1:
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
|
|
|
|
bus_teardown_intr(dev, ch->r_irq, ch->ih);
|
|
|
|
|
bus_release_resource(dev, SYS_RES_IRQ, ATA_IRQ_RID, ch->r_irq);
|
|
|
|
|
ch->r_irq = NULL;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
mtx_destroy(&ch->state_mtx);
|
2004-03-01 13:17:07 +00:00
|
|
|
|
mtx_destroy(&ch->queue_mtx);
|
2003-08-24 09:22:26 +00:00
|
|
|
|
return 0;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
int
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
ata_reinit(device_t dev)
|
2003-08-24 09:22:26 +00:00
|
|
|
|
{
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
struct ata_channel *ch = device_get_softc(dev);
|
2005-09-14 12:45:06 +00:00
|
|
|
|
struct ata_request *request;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
device_t *children;
|
|
|
|
|
int nchildren, i;
|
2004-05-20 14:49:12 +00:00
|
|
|
|
|
2005-09-14 12:45:06 +00:00
|
|
|
|
/* check that we have a valid channel to reinit */
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
if (!ch || !ch->r_irq)
|
2003-08-24 09:22:26 +00:00
|
|
|
|
return ENXIO;
|
|
|
|
|
|
2004-01-11 22:08:34 +00:00
|
|
|
|
if (bootverbose)
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
device_printf(dev, "reiniting channel ..\n");
|
2004-08-27 14:48:32 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* poll for locking the channel */
|
2005-03-31 15:05:40 +00:00
|
|
|
|
while (ATA_LOCKING(dev, ATA_LF_LOCK) != ch->unit)
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
tsleep(&dev, PRIBIO, "atarini", 1);
|
2004-10-06 19:46:08 +00:00
|
|
|
|
|
2006-02-25 17:27:33 +00:00
|
|
|
|
/* catch eventual request in ch->running */
|
2004-09-26 11:48:43 +00:00
|
|
|
|
mtx_lock(&ch->state_mtx);
|
2006-02-25 17:27:33 +00:00
|
|
|
|
if ((request = ch->running))
|
|
|
|
|
callout_stop(&request->callout);
|
|
|
|
|
ch->running = NULL;
|
|
|
|
|
|
|
|
|
|
/* unconditionally grap the channel lock */
|
|
|
|
|
ch->state |= ATA_STALL_QUEUE;
|
2004-09-26 11:48:43 +00:00
|
|
|
|
mtx_unlock(&ch->state_mtx);
|
|
|
|
|
|
2005-04-08 09:37:47 +00:00
|
|
|
|
/* reset the controller HW, the channel and device(s) */
|
2005-04-28 22:08:08 +00:00
|
|
|
|
ATA_RESET(dev);
|
2003-08-24 09:22:26 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* reinit the children and delete any that fails */
|
|
|
|
|
if (!device_get_children(dev, &children, &nchildren)) {
|
|
|
|
|
mtx_lock(&Giant); /* newbus suckage it needs Giant */
|
|
|
|
|
for (i = 0; i < nchildren; i++) {
|
2006-02-25 17:27:33 +00:00
|
|
|
|
/* did any children go missing ? */
|
|
|
|
|
if (children[i] && device_is_attached(children[i]) &&
|
|
|
|
|
ATA_REINIT(children[i])) {
|
|
|
|
|
/*
|
|
|
|
|
* if we had a running request and its device matches
|
|
|
|
|
* this child we need to inform the request that the
|
|
|
|
|
* device is gone.
|
|
|
|
|
*/
|
|
|
|
|
if (request && request->dev == children[i]) {
|
|
|
|
|
request->result = ENXIO;
|
|
|
|
|
device_printf(request->dev, "FAILURE - device detached\n");
|
|
|
|
|
|
|
|
|
|
/* if not timeout finish request here */
|
|
|
|
|
if (!(request->flags & ATA_R_TIMEOUT))
|
2005-09-14 12:45:06 +00:00
|
|
|
|
ata_finish(request);
|
2006-02-25 17:27:33 +00:00
|
|
|
|
request = NULL;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
2006-02-25 17:27:33 +00:00
|
|
|
|
device_delete_child(dev, children[i]);
|
|
|
|
|
}
|
2003-10-07 13:44:15 +00:00
|
|
|
|
}
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
free(children, M_TEMP);
|
|
|
|
|
mtx_unlock(&Giant); /* newbus suckage dealt with, release Giant */
|
2003-08-24 09:22:26 +00:00
|
|
|
|
}
|
2004-05-20 14:49:12 +00:00
|
|
|
|
|
2006-02-25 17:27:33 +00:00
|
|
|
|
/* if we still have a good request put it on the queue again */
|
|
|
|
|
if (request && !(request->flags & ATA_R_TIMEOUT)) {
|
2005-09-14 12:45:06 +00:00
|
|
|
|
device_printf(request->dev,
|
|
|
|
|
"WARNING - %s requeued due to channel reset",
|
|
|
|
|
ata_cmd2str(request));
|
|
|
|
|
if (!(request->flags & (ATA_R_ATAPI | ATA_R_CONTROL)))
|
2006-03-09 08:34:44 +00:00
|
|
|
|
printf(" LBA=%ju", request->u.ata.lba);
|
2005-09-14 12:45:06 +00:00
|
|
|
|
printf("\n");
|
|
|
|
|
request->flags |= ATA_R_REQUEUE;
|
|
|
|
|
ata_queue_request(request);
|
|
|
|
|
}
|
2004-09-26 11:48:43 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* we're done release the channel for new work */
|
2004-10-19 20:13:38 +00:00
|
|
|
|
mtx_lock(&ch->state_mtx);
|
|
|
|
|
ch->state = ATA_IDLE;
|
|
|
|
|
mtx_unlock(&ch->state_mtx);
|
2005-03-31 15:05:40 +00:00
|
|
|
|
ATA_LOCKING(dev, ATA_LF_UNLOCK);
|
2003-08-24 09:22:26 +00:00
|
|
|
|
|
2004-01-11 22:08:34 +00:00
|
|
|
|
if (bootverbose)
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
device_printf(dev, "reinit done ..\n");
|
2004-09-26 11:48:43 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* kick off requests on the queue */
|
|
|
|
|
ata_start(dev);
|
2000-02-18 20:57:33 +00:00
|
|
|
|
return 0;
|
|
|
|
|
}
|
|
|
|
|
|
2003-05-04 09:34:14 +00:00
|
|
|
|
int
|
|
|
|
|
ata_suspend(device_t dev)
|
|
|
|
|
{
|
|
|
|
|
struct ata_channel *ch;
|
|
|
|
|
|
2005-04-21 11:13:39 +00:00
|
|
|
|
/* check for valid device */
|
2003-05-04 09:34:14 +00:00
|
|
|
|
if (!dev || !(ch = device_get_softc(dev)))
|
|
|
|
|
return ENXIO;
|
2004-08-12 08:20:36 +00:00
|
|
|
|
|
2006-04-14 16:25:42 +00:00
|
|
|
|
/* wait for the channel to be IDLE or detached before suspending */
|
|
|
|
|
while (ch->r_irq) {
|
2004-09-26 11:48:43 +00:00
|
|
|
|
mtx_lock(&ch->state_mtx);
|
|
|
|
|
if (ch->state == ATA_IDLE) {
|
|
|
|
|
ch->state = ATA_ACTIVE;
|
2004-10-19 20:13:38 +00:00
|
|
|
|
mtx_unlock(&ch->state_mtx);
|
|
|
|
|
break;
|
2004-09-26 11:48:43 +00:00
|
|
|
|
}
|
|
|
|
|
mtx_unlock(&ch->state_mtx);
|
2004-10-19 20:13:38 +00:00
|
|
|
|
tsleep(ch, PRIBIO, "atasusp", hz/10);
|
2004-09-26 11:48:43 +00:00
|
|
|
|
}
|
2005-03-31 15:05:40 +00:00
|
|
|
|
ATA_LOCKING(dev, ATA_LF_UNLOCK);
|
2003-05-04 09:34:14 +00:00
|
|
|
|
return 0;
|
|
|
|
|
}
|
|
|
|
|
|
2001-03-06 21:43:46 +00:00
|
|
|
|
int
|
2000-02-18 20:57:33 +00:00
|
|
|
|
ata_resume(device_t dev)
|
|
|
|
|
{
|
2002-12-03 20:20:44 +00:00
|
|
|
|
struct ata_channel *ch;
|
|
|
|
|
int error;
|
|
|
|
|
|
2005-04-21 11:13:39 +00:00
|
|
|
|
/* check for valid device */
|
2002-12-03 20:20:44 +00:00
|
|
|
|
if (!dev || !(ch = device_get_softc(dev)))
|
|
|
|
|
return ENXIO;
|
|
|
|
|
|
2005-04-21 11:13:39 +00:00
|
|
|
|
/* reinit the devices, we dont know what mode/state they are in */
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
error = ata_reinit(dev);
|
2001-03-15 15:36:25 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* kick off requests on the queue */
|
|
|
|
|
ata_start(dev);
|
|
|
|
|
return error;
|
2003-08-24 09:22:26 +00:00
|
|
|
|
}
|
2003-03-22 12:18:20 +00:00
|
|
|
|
|
2006-01-18 09:14:55 +00:00
|
|
|
|
int
|
2004-09-26 11:48:43 +00:00
|
|
|
|
ata_interrupt(void *data)
|
|
|
|
|
{
|
|
|
|
|
struct ata_channel *ch = (struct ata_channel *)data;
|
2004-10-13 15:16:35 +00:00
|
|
|
|
struct ata_request *request;
|
2004-09-26 11:48:43 +00:00
|
|
|
|
|
|
|
|
|
mtx_lock(&ch->state_mtx);
|
2004-10-13 15:16:35 +00:00
|
|
|
|
do {
|
2006-01-18 09:14:55 +00:00
|
|
|
|
/* ignore interrupt if its not for us */
|
|
|
|
|
if (ch->hw.status && !ch->hw.status(ch->dev))
|
|
|
|
|
break;
|
|
|
|
|
|
2004-10-13 15:16:35 +00:00
|
|
|
|
/* do we have a running request */
|
2005-09-14 12:45:06 +00:00
|
|
|
|
if (!(request = ch->running))
|
2004-10-13 15:16:35 +00:00
|
|
|
|
break;
|
|
|
|
|
|
|
|
|
|
ATA_DEBUG_RQ(request, "interrupt");
|
|
|
|
|
|
2006-01-18 09:14:55 +00:00
|
|
|
|
/* safetycheck for the right state */
|
2006-02-25 17:27:33 +00:00
|
|
|
|
if (ch->state == ATA_IDLE) {
|
2005-09-14 12:45:06 +00:00
|
|
|
|
device_printf(request->dev, "interrupt on idle channel ignored\n");
|
2004-10-13 15:16:35 +00:00
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/*
|
2006-03-09 10:24:03 +00:00
|
|
|
|
* we have the HW locks, so end the transaction for this request
|
2005-04-21 11:13:39 +00:00
|
|
|
|
* if it finishes immediately otherwise wait for next interrupt
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
*/
|
2004-10-13 15:16:35 +00:00
|
|
|
|
if (ch->hw.end_transaction(request) == ATA_OP_FINISHED) {
|
2004-09-26 11:48:43 +00:00
|
|
|
|
ch->running = NULL;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
if (ch->state == ATA_ACTIVE)
|
2004-09-26 11:48:43 +00:00
|
|
|
|
ch->state = ATA_IDLE;
|
|
|
|
|
mtx_unlock(&ch->state_mtx);
|
2005-03-31 15:05:40 +00:00
|
|
|
|
ATA_LOCKING(ch->dev, ATA_LF_UNLOCK);
|
2004-09-26 11:48:43 +00:00
|
|
|
|
ata_finish(request);
|
2006-01-18 09:14:55 +00:00
|
|
|
|
return 1;
|
2004-09-26 11:48:43 +00:00
|
|
|
|
}
|
2004-10-13 15:16:35 +00:00
|
|
|
|
} while (0);
|
|
|
|
|
mtx_unlock(&ch->state_mtx);
|
2006-01-18 09:14:55 +00:00
|
|
|
|
return 0;
|
2004-09-26 11:48:43 +00:00
|
|
|
|
}
|
|
|
|
|
|
2003-08-24 09:22:26 +00:00
|
|
|
|
/*
|
|
|
|
|
* device related interfaces
|
|
|
|
|
*/
|
|
|
|
|
static int
|
2005-05-16 13:07:27 +00:00
|
|
|
|
ata_ioctl(struct cdev *dev, u_long cmd, caddr_t data,
|
2004-09-26 11:48:43 +00:00
|
|
|
|
int32_t flag, struct thread *td)
|
2003-08-24 09:22:26 +00:00
|
|
|
|
{
|
2005-05-16 13:07:27 +00:00
|
|
|
|
device_t device, *children;
|
|
|
|
|
struct ata_ioc_devices *devices = (struct ata_ioc_devices *)data;
|
|
|
|
|
int *value = (int *)data;
|
|
|
|
|
int i, nchildren, error = ENOTTY;
|
|
|
|
|
|
|
|
|
|
switch (cmd) {
|
|
|
|
|
case IOCATAGMAXCHANNEL:
|
|
|
|
|
*value = devclass_get_maxunit(ata_devclass);
|
|
|
|
|
error = 0;
|
|
|
|
|
break;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case IOCATAREINIT:
|
|
|
|
|
if (*value > devclass_get_maxunit(ata_devclass) ||
|
|
|
|
|
!(device = devclass_get_device(ata_devclass, *value)))
|
|
|
|
|
return ENXIO;
|
|
|
|
|
error = ata_reinit(device);
|
|
|
|
|
ata_start(device);
|
2003-08-24 09:22:26 +00:00
|
|
|
|
break;
|
2002-03-30 16:36:41 +00:00
|
|
|
|
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case IOCATAATTACH:
|
|
|
|
|
if (*value > devclass_get_maxunit(ata_devclass) ||
|
|
|
|
|
!(device = devclass_get_device(ata_devclass, *value)))
|
|
|
|
|
return ENXIO;
|
|
|
|
|
/* XXX SOS should enable channel HW on controller */
|
|
|
|
|
error = ata_attach(device);
|
|
|
|
|
break;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case IOCATADETACH:
|
|
|
|
|
if (*value > devclass_get_maxunit(ata_devclass) ||
|
|
|
|
|
!(device = devclass_get_device(ata_devclass, *value)))
|
|
|
|
|
return ENXIO;
|
|
|
|
|
error = ata_detach(device);
|
|
|
|
|
/* XXX SOS should disable channel HW on controller */
|
2003-08-24 09:22:26 +00:00
|
|
|
|
break;
|
2002-04-02 13:48:17 +00:00
|
|
|
|
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case IOCATADEVICES:
|
|
|
|
|
if (devices->channel > devclass_get_maxunit(ata_devclass) ||
|
|
|
|
|
!(device = devclass_get_device(ata_devclass, devices->channel)))
|
|
|
|
|
return ENXIO;
|
|
|
|
|
bzero(devices->name[0], 32);
|
|
|
|
|
bzero(&devices->params[0], sizeof(struct ata_params));
|
|
|
|
|
bzero(devices->name[1], 32);
|
|
|
|
|
bzero(&devices->params[1], sizeof(struct ata_params));
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
if (!device_get_children(device, &children, &nchildren)) {
|
|
|
|
|
for (i = 0; i < nchildren; i++) {
|
2005-05-16 13:07:27 +00:00
|
|
|
|
if (children[i] && device_is_attached(children[i])) {
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
struct ata_device *atadev = device_get_softc(children[i]);
|
|
|
|
|
|
|
|
|
|
if (atadev->unit == ATA_MASTER) {
|
2005-05-16 13:07:27 +00:00
|
|
|
|
strncpy(devices->name[0],
|
|
|
|
|
device_get_nameunit(children[i]), 32);
|
|
|
|
|
bcopy(&atadev->param, &devices->params[0],
|
|
|
|
|
sizeof(struct ata_params));
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
|
|
|
|
if (atadev->unit == ATA_SLAVE) {
|
2005-05-16 13:07:27 +00:00
|
|
|
|
strncpy(devices->name[1],
|
|
|
|
|
device_get_nameunit(children[i]), 32);
|
|
|
|
|
bcopy(&atadev->param, &devices->params[1],
|
|
|
|
|
sizeof(struct ata_params));
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
free(children, M_TEMP);
|
|
|
|
|
error = 0;
|
2003-08-24 09:22:26 +00:00
|
|
|
|
}
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
else
|
2005-05-16 13:07:27 +00:00
|
|
|
|
error = ENODEV;
|
2003-08-24 09:22:26 +00:00
|
|
|
|
break;
|
2003-05-02 12:41:44 +00:00
|
|
|
|
|
2005-05-16 13:07:27 +00:00
|
|
|
|
default:
|
|
|
|
|
if (ata_raid_ioctl_func)
|
|
|
|
|
error = ata_raid_ioctl_func(cmd, data);
|
|
|
|
|
}
|
|
|
|
|
return error;
|
|
|
|
|
}
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
|
2005-05-16 13:07:27 +00:00
|
|
|
|
int
|
|
|
|
|
ata_device_ioctl(device_t dev, u_long cmd, caddr_t data)
|
|
|
|
|
{
|
|
|
|
|
struct ata_device *atadev = device_get_softc(dev);
|
|
|
|
|
struct ata_ioc_request *ioc_request = (struct ata_ioc_request *)data;
|
|
|
|
|
struct ata_params *params = (struct ata_params *)data;
|
|
|
|
|
int *mode = (int *)data;
|
|
|
|
|
struct ata_request *request;
|
|
|
|
|
caddr_t buf;
|
|
|
|
|
int error;
|
|
|
|
|
|
|
|
|
|
switch (cmd) {
|
|
|
|
|
case IOCATAREQUEST:
|
|
|
|
|
if (!(buf = malloc(ioc_request->count, M_ATA, M_NOWAIT))) {
|
|
|
|
|
return ENOMEM;
|
|
|
|
|
}
|
|
|
|
|
if (!(request = ata_alloc_request())) {
|
|
|
|
|
free(buf, M_ATA);
|
|
|
|
|
return ENOMEM;
|
|
|
|
|
}
|
|
|
|
|
if (ioc_request->flags & ATA_CMD_WRITE) {
|
|
|
|
|
error = copyin(ioc_request->data, buf, ioc_request->count);
|
|
|
|
|
if (error) {
|
|
|
|
|
free(buf, M_ATA);
|
|
|
|
|
ata_free_request(request);
|
|
|
|
|
return error;
|
2001-08-30 09:47:17 +00:00
|
|
|
|
}
|
2002-03-10 21:03:04 +00:00
|
|
|
|
}
|
2005-05-16 13:07:27 +00:00
|
|
|
|
request->dev = dev;
|
|
|
|
|
if (ioc_request->flags & ATA_CMD_ATAPI) {
|
|
|
|
|
request->flags = ATA_R_ATAPI;
|
|
|
|
|
bcopy(ioc_request->u.atapi.ccb, request->u.atapi.ccb, 16);
|
|
|
|
|
}
|
|
|
|
|
else {
|
|
|
|
|
request->u.ata.command = ioc_request->u.ata.command;
|
|
|
|
|
request->u.ata.feature = ioc_request->u.ata.feature;
|
|
|
|
|
request->u.ata.lba = ioc_request->u.ata.lba;
|
|
|
|
|
request->u.ata.count = ioc_request->u.ata.count;
|
|
|
|
|
}
|
|
|
|
|
request->timeout = ioc_request->timeout;
|
|
|
|
|
request->data = buf;
|
|
|
|
|
request->bytecount = ioc_request->count;
|
|
|
|
|
request->transfersize = request->bytecount;
|
|
|
|
|
if (ioc_request->flags & ATA_CMD_CONTROL)
|
|
|
|
|
request->flags |= ATA_R_CONTROL;
|
|
|
|
|
if (ioc_request->flags & ATA_CMD_READ)
|
|
|
|
|
request->flags |= ATA_R_READ;
|
|
|
|
|
if (ioc_request->flags & ATA_CMD_WRITE)
|
|
|
|
|
request->flags |= ATA_R_WRITE;
|
|
|
|
|
ata_queue_request(request);
|
2006-03-31 08:09:05 +00:00
|
|
|
|
if (request->flags & ATA_R_ATAPI) {
|
|
|
|
|
bcopy(&request->u.atapi.sense, &ioc_request->u.atapi.sense,
|
|
|
|
|
sizeof(struct atapi_sense));
|
|
|
|
|
}
|
|
|
|
|
else {
|
2005-05-16 13:07:27 +00:00
|
|
|
|
ioc_request->u.ata.command = request->u.ata.command;
|
|
|
|
|
ioc_request->u.ata.feature = request->u.ata.feature;
|
|
|
|
|
ioc_request->u.ata.lba = request->u.ata.lba;
|
|
|
|
|
ioc_request->u.ata.count = request->u.ata.count;
|
|
|
|
|
}
|
|
|
|
|
ioc_request->error = request->result;
|
|
|
|
|
if (ioc_request->flags & ATA_CMD_READ)
|
|
|
|
|
error = copyout(buf, ioc_request->data, ioc_request->count);
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
else
|
2005-05-16 13:07:27 +00:00
|
|
|
|
error = 0;
|
|
|
|
|
free(buf, M_ATA);
|
|
|
|
|
ata_free_request(request);
|
|
|
|
|
return error;
|
|
|
|
|
|
|
|
|
|
case IOCATAGPARM:
|
2005-11-25 09:00:56 +00:00
|
|
|
|
ata_getparam(atadev, 0);
|
2005-05-16 13:07:27 +00:00
|
|
|
|
bcopy(&atadev->param, params, sizeof(struct ata_params));
|
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
|
|
case IOCATASMODE:
|
|
|
|
|
atadev->mode = *mode;
|
|
|
|
|
ATA_SETMODE(device_get_parent(dev), dev);
|
|
|
|
|
return 0;
|
2004-05-20 14:49:12 +00:00
|
|
|
|
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case IOCATAGMODE:
|
|
|
|
|
*mode = atadev->mode;
|
|
|
|
|
return 0;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
default:
|
2005-05-16 13:07:27 +00:00
|
|
|
|
return ENOTTY;
|
Finally!!
The much roumored replacement for our current IDE/ATA/ATAPI is
materialising in the CVS repositories around the globe.
So what does this bring us:
A new reengineered ATA/ATAPI subsystem, that tries to overcome
most of the deficiencies with the current drivers.
It supports PCI as well as ISA devices without all the hackery
in ide_pci.c to make PCI devices look like ISA counterparts.
It doesn't have the excessive wait problem on probe, in fact you
shouldn't notice any delay when your devices are getting probed.
Probing and attaching of devices are postponed until interrupts
are enabled (well almost, not finished yet for disks), making
things alot cleaner.
Improved performance, although DMA support is still WIP and not
in this pre alpha release, worldstone is faster with the new
driver compared to the old even with DMA.
So what does it take away:
There is NO support for old MFM/RLL/ESDI disks.
There is NO support for bad144, if your disk is bad, ditch it, it has
already outgrown its internal spare sectors, and is dying.
For you to try this out, you will have to modify your kernel config
file to use the "ata" controller instead of all wdc? entries.
example:
# for a PCI only system (most modern machines)
controller ata0
device atadisk0 # ATA disks
device atapicd0 # ATAPI CDROM's
device atapist0 # ATAPI tapes
#You should add the following on ISA systems:
controller ata1 at isa? port "IO_WD1" bio irq 14
controller ata2 at isa? port "IO_WD2" bio irq 15
You can leave it all in there, the system knows how to manage.
For now this driver reuses the device entries from the old system
(that will probably change later), but remember that disks are
now numbered in the sequence they are found (like the SCSI system)
not as absolute positions as the old system.
Although I have tested this on all the systems I can get my hands on,
there might very well be gremlins in there, so use AT YOU OWN RISK!!
This is still WIP, so there are lots of rough edges and unfinished
things in there, and what I have in my lab might look very different
from whats in CVS at any given time. So please have all eventual
changes go through me, or chances are they just dissapears...
I would very much like to hear from you, both good and bad news
are very welcome.
Enjoy!!
-Søren
1999-03-01 21:19:19 +00:00
|
|
|
|
}
|
Ten'th update to the new ATA/ATAPI driver:
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-09-21 19:50:40 +00:00
|
|
|
|
}
|
|
|
|
|
|
2004-05-20 14:49:12 +00:00
|
|
|
|
static void
|
2003-08-24 09:22:26 +00:00
|
|
|
|
ata_boot_attach(void)
|
2003-05-02 13:47:44 +00:00
|
|
|
|
{
|
|
|
|
|
struct ata_channel *ch;
|
|
|
|
|
int ctlr;
|
|
|
|
|
|
2005-10-27 16:32:39 +00:00
|
|
|
|
mtx_lock(&Giant); /* newbus suckage it needs Giant */
|
2004-09-09 13:25:46 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* kick of probe and attach on all channels */
|
|
|
|
|
for (ctlr = 0; ctlr < devclass_get_maxunit(ata_devclass); ctlr++) {
|
|
|
|
|
if ((ch = devclass_get_softc(ata_devclass, ctlr))) {
|
2005-04-15 10:20:52 +00:00
|
|
|
|
ata_identify(ch->dev);
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
1999-03-05 09:43:30 +00:00
|
|
|
|
}
|
2005-10-27 16:32:39 +00:00
|
|
|
|
|
|
|
|
|
/* release the hook that got us here, we are only needed once during boot */
|
|
|
|
|
if (ata_delayed_attach) {
|
|
|
|
|
config_intrhook_disestablish(ata_delayed_attach);
|
|
|
|
|
free(ata_delayed_attach, M_TEMP);
|
2006-02-09 20:54:42 +00:00
|
|
|
|
ata_delayed_attach = NULL;
|
2005-10-27 16:32:39 +00:00
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
mtx_unlock(&Giant); /* newbus suckage dealt with, release Giant */
|
Major update of the ATA RAID code, part 1:
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
|
|
|
|
}
|
|
|
|
|
|
2005-04-21 11:13:39 +00:00
|
|
|
|
|
2003-08-24 09:22:26 +00:00
|
|
|
|
/*
|
|
|
|
|
* misc support functions
|
|
|
|
|
*/
|
2005-04-21 11:13:39 +00:00
|
|
|
|
static device_t
|
2005-04-15 10:20:52 +00:00
|
|
|
|
ata_add_child(device_t parent, struct ata_device *atadev, int unit)
|
2002-03-30 16:36:41 +00:00
|
|
|
|
{
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
device_t child;
|
|
|
|
|
|
2005-04-15 10:20:52 +00:00
|
|
|
|
if ((child = device_add_child(parent, NULL, unit))) {
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
device_set_softc(child, atadev);
|
|
|
|
|
device_quiet(child);
|
|
|
|
|
atadev->dev = child;
|
|
|
|
|
atadev->max_iosize = DEV_BSIZE;
|
|
|
|
|
atadev->mode = ATA_PIO_MAX;
|
2005-04-29 11:30:03 +00:00
|
|
|
|
}
|
|
|
|
|
return child;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static int
|
2005-11-25 09:00:56 +00:00
|
|
|
|
ata_getparam(struct ata_device *atadev, int init)
|
2005-04-29 11:30:03 +00:00
|
|
|
|
{
|
2005-11-25 09:00:56 +00:00
|
|
|
|
struct ata_channel *ch = device_get_softc(device_get_parent(atadev->dev));
|
2005-04-29 11:30:03 +00:00
|
|
|
|
struct ata_request *request;
|
|
|
|
|
u_int8_t command = 0;
|
|
|
|
|
int error = ENOMEM, retries = 2;
|
|
|
|
|
|
|
|
|
|
if (ch->devices &
|
|
|
|
|
(atadev->unit == ATA_MASTER ? ATA_ATA_MASTER : ATA_ATA_SLAVE))
|
|
|
|
|
command = ATA_ATA_IDENTIFY;
|
|
|
|
|
if (ch->devices &
|
|
|
|
|
(atadev->unit == ATA_MASTER ? ATA_ATAPI_MASTER : ATA_ATAPI_SLAVE))
|
|
|
|
|
command = ATA_ATAPI_IDENTIFY;
|
|
|
|
|
if (!command)
|
|
|
|
|
return ENXIO;
|
|
|
|
|
|
|
|
|
|
while (retries-- > 0 && error) {
|
|
|
|
|
if (!(request = ata_alloc_request()))
|
|
|
|
|
break;
|
|
|
|
|
request->dev = atadev->dev;
|
|
|
|
|
request->timeout = 1;
|
|
|
|
|
request->retries = 0;
|
|
|
|
|
request->u.ata.command = command;
|
|
|
|
|
request->flags = (ATA_R_READ|ATA_R_AT_HEAD|ATA_R_DIRECT|ATA_R_QUIET);
|
|
|
|
|
request->data = (void *)&atadev->param;
|
|
|
|
|
request->bytecount = sizeof(struct ata_params);
|
|
|
|
|
request->donecount = 0;
|
|
|
|
|
request->transfersize = DEV_BSIZE;
|
|
|
|
|
ata_queue_request(request);
|
|
|
|
|
error = request->result;
|
|
|
|
|
ata_free_request(request);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
if (!error && (isprint(atadev->param.model[0]) ||
|
|
|
|
|
isprint(atadev->param.model[1]))) {
|
|
|
|
|
struct ata_params *atacap = &atadev->param;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
char buffer[64];
|
2005-04-29 11:30:03 +00:00
|
|
|
|
#if BYTE_ORDER == BIG_ENDIAN
|
|
|
|
|
int16_t *ptr;
|
|
|
|
|
|
|
|
|
|
for (ptr = (int16_t *)atacap;
|
|
|
|
|
ptr < (int16_t *)atacap + sizeof(struct ata_params)/2; ptr++) {
|
|
|
|
|
*ptr = bswap16(*ptr);
|
|
|
|
|
}
|
|
|
|
|
#endif
|
|
|
|
|
if (!(!strncmp(atacap->model, "FX", 2) ||
|
|
|
|
|
!strncmp(atacap->model, "NEC", 3) ||
|
|
|
|
|
!strncmp(atacap->model, "Pioneer", 7) ||
|
|
|
|
|
!strncmp(atacap->model, "SHARP", 5))) {
|
|
|
|
|
bswap(atacap->model, sizeof(atacap->model));
|
|
|
|
|
bswap(atacap->revision, sizeof(atacap->revision));
|
|
|
|
|
bswap(atacap->serial, sizeof(atacap->serial));
|
|
|
|
|
}
|
|
|
|
|
btrim(atacap->model, sizeof(atacap->model));
|
|
|
|
|
bpack(atacap->model, atacap->model, sizeof(atacap->model));
|
|
|
|
|
btrim(atacap->revision, sizeof(atacap->revision));
|
|
|
|
|
bpack(atacap->revision, atacap->revision, sizeof(atacap->revision));
|
|
|
|
|
btrim(atacap->serial, sizeof(atacap->serial));
|
|
|
|
|
bpack(atacap->serial, atacap->serial, sizeof(atacap->serial));
|
2005-11-25 09:00:56 +00:00
|
|
|
|
|
2005-04-29 11:30:03 +00:00
|
|
|
|
if (bootverbose)
|
|
|
|
|
printf("ata%d-%s: pio=%s wdma=%s udma=%s cable=%s wire\n",
|
2006-03-10 12:20:53 +00:00
|
|
|
|
device_get_unit(ch->dev),
|
|
|
|
|
atadev->unit == ATA_MASTER ? "master" : "slave",
|
2005-04-29 11:30:03 +00:00
|
|
|
|
ata_mode2str(ata_pmode(atacap)),
|
|
|
|
|
ata_mode2str(ata_wmode(atacap)),
|
|
|
|
|
ata_mode2str(ata_umode(atacap)),
|
|
|
|
|
(atacap->hwres & ATA_CABLE_ID) ? "80":"40");
|
|
|
|
|
|
2005-11-25 09:00:56 +00:00
|
|
|
|
if (init) {
|
|
|
|
|
sprintf(buffer, "%.40s/%.8s", atacap->model, atacap->revision);
|
|
|
|
|
device_set_desc_copy(atadev->dev, buffer);
|
|
|
|
|
if (atadev->param.config & ATA_PROTO_ATAPI) {
|
|
|
|
|
if (atapi_dma && ch->dma &&
|
|
|
|
|
(atadev->param.config & ATA_DRQ_MASK) != ATA_DRQ_INTR &&
|
|
|
|
|
ata_umode(&atadev->param) >= ATA_UDMA2)
|
|
|
|
|
atadev->mode = ATA_DMA_MAX;
|
|
|
|
|
}
|
|
|
|
|
else {
|
|
|
|
|
if (ata_dma && ch->dma &&
|
|
|
|
|
(ata_umode(&atadev->param) > 0 ||
|
|
|
|
|
ata_wmode(&atadev->param) > 0))
|
|
|
|
|
atadev->mode = ATA_DMA_MAX;
|
|
|
|
|
}
|
2003-08-24 09:22:26 +00:00
|
|
|
|
}
|
2003-01-27 09:04:29 +00:00
|
|
|
|
}
|
2005-04-29 11:30:03 +00:00
|
|
|
|
else {
|
|
|
|
|
if (!error)
|
|
|
|
|
error = ENXIO;
|
|
|
|
|
}
|
|
|
|
|
return error;
|
Major update of the ATA RAID code, part 1:
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
|
|
|
|
}
|
|
|
|
|
|
2005-04-20 12:51:54 +00:00
|
|
|
|
int
|
2005-04-15 10:20:52 +00:00
|
|
|
|
ata_identify(device_t dev)
|
Major update of the ATA RAID code, part 1:
Overhaul of the attach/detach code and structures, there were some nasty
bugs in the old implementation. This made it possible to collapse the
ATA/ATAPI device control structures into one generic structure.
A note here, the kernel is NOT ready for detach of active devices,
it fails all over in random places, but for inactive devices it works.
However for ATA RAID this works, since the RAID abstration layer
insulates the buggy^H^H^H^H^H^Hfragile device subsystem from the
physical disks.
Proberly detect the RAID's from the BIOS, and mark critical RAID1
arrays as such, but continue if there is enough of the mirror left
to do so.
Properly fail arrays on a live system. For RAID0 that means return EIO,
and for RAID1 it means continue on the still working part of the mirror
if possible, else return EIO.
If the state changes, log this to the console.
Allow for Promise & Highpoint controllers/arrays to coexist on the
same machine. It is not possible to distribute arrays over different
makes of controllers though.
If Promise SuperSwap enclosures are used, signal disk state on the
status LED on the front.
Misc fixes that I had lying around for various minor bugs.
Sponsored by: Advanis Inc.
2002-02-04 19:23:40 +00:00
|
|
|
|
{
|
2005-04-15 10:20:52 +00:00
|
|
|
|
struct ata_channel *ch = device_get_softc(dev);
|
2005-04-29 11:30:03 +00:00
|
|
|
|
struct ata_device *master = NULL, *slave = NULL;
|
|
|
|
|
device_t master_child = NULL, slave_child = NULL;
|
|
|
|
|
int master_unit = -1, slave_unit = -1;
|
|
|
|
|
|
|
|
|
|
if (ch->devices & (ATA_ATA_MASTER | ATA_ATAPI_MASTER)) {
|
2005-04-30 16:22:07 +00:00
|
|
|
|
if (!(master = malloc(sizeof(struct ata_device),
|
2005-04-29 11:30:03 +00:00
|
|
|
|
M_ATA, M_NOWAIT | M_ZERO))) {
|
|
|
|
|
device_printf(dev, "out of memory\n");
|
|
|
|
|
return ENOMEM;
|
2005-04-30 16:22:07 +00:00
|
|
|
|
}
|
|
|
|
|
master->unit = ATA_MASTER;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
2005-04-29 11:30:03 +00:00
|
|
|
|
if (ch->devices & (ATA_ATA_SLAVE | ATA_ATAPI_SLAVE)) {
|
2005-04-30 16:22:07 +00:00
|
|
|
|
if (!(slave = malloc(sizeof(struct ata_device),
|
2005-04-29 11:30:03 +00:00
|
|
|
|
M_ATA, M_NOWAIT | M_ZERO))) {
|
|
|
|
|
free(master, M_ATA);
|
|
|
|
|
device_printf(dev, "out of memory\n");
|
|
|
|
|
return ENOMEM;
|
2005-04-30 16:22:07 +00:00
|
|
|
|
}
|
|
|
|
|
slave->unit = ATA_SLAVE;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
2004-05-20 14:49:12 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
#ifdef ATA_STATIC_ID
|
2005-04-29 11:30:03 +00:00
|
|
|
|
if (ch->devices & ATA_ATA_MASTER)
|
|
|
|
|
master_unit = (device_get_unit(dev) << 1);
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
#endif
|
2005-04-29 11:30:03 +00:00
|
|
|
|
if (master && !(master_child = ata_add_child(dev, master, master_unit))) {
|
|
|
|
|
free(master, M_ATA);
|
|
|
|
|
master = NULL;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
2005-04-15 10:20:52 +00:00
|
|
|
|
#ifdef ATA_STATIC_ID
|
2005-04-29 11:30:03 +00:00
|
|
|
|
if (ch->devices & ATA_ATA_SLAVE)
|
|
|
|
|
slave_unit = (device_get_unit(dev) << 1) + 1;
|
2005-04-15 10:20:52 +00:00
|
|
|
|
#endif
|
2005-04-29 11:30:03 +00:00
|
|
|
|
if (slave && !(slave_child = ata_add_child(dev, slave, slave_unit))) {
|
|
|
|
|
free(slave, M_ATA);
|
|
|
|
|
slave = NULL;
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
2000-09-19 11:08:39 +00:00
|
|
|
|
|
2005-11-25 09:00:56 +00:00
|
|
|
|
if (slave && ata_getparam(slave, 1)) {
|
2005-04-29 11:30:03 +00:00
|
|
|
|
device_delete_child(dev, slave_child);
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
free(slave, M_ATA);
|
2005-04-29 11:30:03 +00:00
|
|
|
|
}
|
2005-11-25 09:00:56 +00:00
|
|
|
|
if (master && ata_getparam(master, 1)) {
|
2005-04-29 11:30:03 +00:00
|
|
|
|
device_delete_child(dev, master_child);
|
|
|
|
|
free(master, M_ATA);
|
|
|
|
|
}
|
2005-04-15 10:20:52 +00:00
|
|
|
|
|
|
|
|
|
bus_generic_probe(dev);
|
|
|
|
|
bus_generic_attach(dev);
|
|
|
|
|
return 0;
|
2001-02-06 12:41:53 +00:00
|
|
|
|
}
|
|
|
|
|
|
2005-04-06 10:22:56 +00:00
|
|
|
|
void
|
2005-04-30 16:22:07 +00:00
|
|
|
|
ata_default_registers(device_t dev)
|
2005-04-06 10:22:56 +00:00
|
|
|
|
{
|
2005-04-30 16:22:07 +00:00
|
|
|
|
struct ata_channel *ch = device_get_softc(dev);
|
|
|
|
|
|
2005-04-06 10:22:56 +00:00
|
|
|
|
/* fill in the defaults from whats setup already */
|
|
|
|
|
ch->r_io[ATA_ERROR].res = ch->r_io[ATA_FEATURE].res;
|
|
|
|
|
ch->r_io[ATA_ERROR].offset = ch->r_io[ATA_FEATURE].offset;
|
|
|
|
|
ch->r_io[ATA_IREASON].res = ch->r_io[ATA_COUNT].res;
|
|
|
|
|
ch->r_io[ATA_IREASON].offset = ch->r_io[ATA_COUNT].offset;
|
|
|
|
|
ch->r_io[ATA_STATUS].res = ch->r_io[ATA_COMMAND].res;
|
|
|
|
|
ch->r_io[ATA_STATUS].offset = ch->r_io[ATA_COMMAND].offset;
|
|
|
|
|
ch->r_io[ATA_ALTSTAT].res = ch->r_io[ATA_CONTROL].res;
|
|
|
|
|
ch->r_io[ATA_ALTSTAT].offset = ch->r_io[ATA_CONTROL].offset;
|
|
|
|
|
}
|
|
|
|
|
|
2005-08-17 15:00:33 +00:00
|
|
|
|
void
|
2005-05-03 07:55:07 +00:00
|
|
|
|
ata_modify_if_48bit(struct ata_request *request)
|
|
|
|
|
{
|
2005-08-17 15:00:33 +00:00
|
|
|
|
struct ata_channel *ch = device_get_softc(device_get_parent(request->dev));
|
2005-05-03 07:55:07 +00:00
|
|
|
|
struct ata_device *atadev = device_get_softc(request->dev);
|
|
|
|
|
|
2005-05-17 12:31:54 +00:00
|
|
|
|
atadev->flags &= ~ATA_D_48BIT_ACTIVE;
|
|
|
|
|
|
2005-05-03 07:55:07 +00:00
|
|
|
|
if ((request->u.ata.lba >= ATA_MAX_28BIT_LBA ||
|
|
|
|
|
request->u.ata.count > 256) &&
|
|
|
|
|
atadev->param.support.command2 & ATA_SUPPORT_ADDRESS48) {
|
|
|
|
|
|
2005-05-16 13:07:27 +00:00
|
|
|
|
/* translate command into 48bit version */
|
2005-08-17 15:00:33 +00:00
|
|
|
|
switch (request->u.ata.command) {
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_READ:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
request->u.ata.command = ATA_READ48;
|
|
|
|
|
break;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_READ_MUL:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
request->u.ata.command = ATA_READ_MUL48;
|
|
|
|
|
break;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_READ_DMA:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
if (ch->flags & ATA_NO_48BIT_DMA) {
|
|
|
|
|
if (request->transfersize > DEV_BSIZE)
|
|
|
|
|
request->u.ata.command = ATA_READ_MUL48;
|
|
|
|
|
else
|
|
|
|
|
request->u.ata.command = ATA_READ48;
|
|
|
|
|
request->flags &= ~ATA_R_DMA;
|
|
|
|
|
}
|
|
|
|
|
else
|
|
|
|
|
request->u.ata.command = ATA_READ_DMA48;
|
|
|
|
|
break;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_READ_DMA_QUEUED:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
if (ch->flags & ATA_NO_48BIT_DMA) {
|
|
|
|
|
if (request->transfersize > DEV_BSIZE)
|
|
|
|
|
request->u.ata.command = ATA_READ_MUL48;
|
|
|
|
|
else
|
|
|
|
|
request->u.ata.command = ATA_READ48;
|
|
|
|
|
request->flags &= ~ATA_R_DMA;
|
|
|
|
|
}
|
|
|
|
|
else
|
|
|
|
|
request->u.ata.command = ATA_READ_DMA_QUEUED48;
|
|
|
|
|
break;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_WRITE:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
request->u.ata.command = ATA_WRITE48;
|
|
|
|
|
break;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_WRITE_MUL:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
request->u.ata.command = ATA_WRITE_MUL48;
|
|
|
|
|
break;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_WRITE_DMA:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
if (ch->flags & ATA_NO_48BIT_DMA) {
|
|
|
|
|
if (request->transfersize > DEV_BSIZE)
|
|
|
|
|
request->u.ata.command = ATA_WRITE_MUL48;
|
|
|
|
|
else
|
|
|
|
|
request->u.ata.command = ATA_WRITE48;
|
|
|
|
|
request->flags &= ~ATA_R_DMA;
|
|
|
|
|
}
|
|
|
|
|
else
|
|
|
|
|
request->u.ata.command = ATA_WRITE_DMA48;
|
|
|
|
|
break;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_WRITE_DMA_QUEUED:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
if (ch->flags & ATA_NO_48BIT_DMA) {
|
|
|
|
|
if (request->transfersize > DEV_BSIZE)
|
|
|
|
|
request->u.ata.command = ATA_WRITE_MUL48;
|
|
|
|
|
else
|
|
|
|
|
request->u.ata.command = ATA_WRITE48;
|
|
|
|
|
request->u.ata.command = ATA_WRITE48;
|
|
|
|
|
request->flags &= ~ATA_R_DMA;
|
|
|
|
|
}
|
|
|
|
|
else
|
|
|
|
|
request->u.ata.command = ATA_WRITE_DMA_QUEUED48;
|
|
|
|
|
break;
|
2005-05-16 13:07:27 +00:00
|
|
|
|
case ATA_FLUSHCACHE:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
request->u.ata.command = ATA_FLUSHCACHE48;
|
|
|
|
|
break;
|
2005-11-25 09:00:56 +00:00
|
|
|
|
case ATA_READ_NATIVE_MAX_ADDDRESS:
|
|
|
|
|
request->u.ata.command = ATA_READ_NATIVE_MAX_ADDDRESS48;
|
|
|
|
|
break;
|
|
|
|
|
case ATA_SET_MAX_ADDRESS:
|
|
|
|
|
request->u.ata.command = ATA_SET_MAX_ADDRESS48;
|
|
|
|
|
break;
|
2005-05-03 07:55:07 +00:00
|
|
|
|
default:
|
2005-08-17 15:00:33 +00:00
|
|
|
|
return;
|
2005-05-03 07:55:07 +00:00
|
|
|
|
}
|
|
|
|
|
atadev->flags |= ATA_D_48BIT_ACTIVE;
|
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
|
2000-09-19 11:08:39 +00:00
|
|
|
|
void
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
ata_udelay(int interval)
|
2000-09-19 11:08:39 +00:00
|
|
|
|
{
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/* for now just use DELAY, the timer/sleep subsytems are not there yet */
|
|
|
|
|
if (1 || interval < (1000000/hz) || ata_delayed_attach)
|
|
|
|
|
DELAY(interval);
|
|
|
|
|
else
|
|
|
|
|
tsleep(&interval, PRIBIO, "ataslp", interval/(1000000/hz));
|
2000-09-19 11:08:39 +00:00
|
|
|
|
}
|
2004-05-20 14:49:12 +00:00
|
|
|
|
|
2000-09-19 11:08:39 +00:00
|
|
|
|
char *
|
|
|
|
|
ata_mode2str(int mode)
|
Ten'th update to the new ATA/ATAPI driver:
It been awhile since the last major update, as a benefit there
are some cool things in this one (and new bugs probably :) )...
The ATA driver has grown "real" timeout support for all devices.
This means that it should be possible to get in contact with
(especially) lost ATAPI devices. It also means that the ATA
driver is now usable on notebooks as it will DTRT on resume.
An experimental hack at utilizing the Promise66's at UDMA66 is
in there, but I cant test it. If someone feels like sending
me one, give me a ping.
The ATAPI DMA enableling scheme has been changed, also better DMA
support for the Aladdin chipset has been implemented for ATAPI
devices. Note that the Aladdin apparently only can do DMA reads
on ATAPI devices, and the Promise cant do ATAPI DMA at all.
I have seen problems on some ATAPI devices that should be able
to run in DMA mode, so if you encounter problems with hanging
atapi devices during the probe, or during access, disable DMA
in atapi-all.c, and let me know. It might be nessesary to do this
via a "white list" for known good devices...
The ATAPI CDROM driver can now use eject/close without hanging and
the bug that caused reading beyond the end of a CD has been fixed.
Media change is also handled proberly. DVD drives are identified
and are usable as CDROM devices at least, I dont have the HW to
test this further, see above :).
The ATAPI tape driver has gotten some support for using the DSC
method for not blocking the IDE channel during read/write when
the device has full buffers. It knows about the OnStream DI-30
device, support is not completed yet, but it can function as a
primitive backup medium, without filemarks, and without bad media
handeling. This is because the OnStream device doesn't handle this
(like everybody else) in HW. It also now supports getting/setting
the record position on devices that supports it.
Some rather major cleanups and rearrangements as well (cvs -b diff
is your freind). I'm closing in on declaring this for beta code,
most of the infrastruture is in place by now.
As usual USE AT YOUR OWN RISK!!, this is still alpha level code.
This driver can hose your disk real bad if anything goes wrong, but
now you have been warned :)
But please tell me how it works for you!
Enjoy!
-Søren
1999-09-21 19:50:40 +00:00
|
|
|
|
{
|
|
|
|
|
switch (mode) {
|
2005-08-29 18:19:06 +00:00
|
|
|
|
case -1: return "UNSUPPORTED";
|
2000-01-03 10:26:59 +00:00
|
|
|
|
case ATA_PIO0: return "PIO0";
|
|
|
|
|
case ATA_PIO1: return "PIO1";
|
|
|
|
|
case ATA_PIO2: return "PIO2";
|
|
|
|
|
case ATA_PIO3: return "PIO3";
|
|
|
|
|
case ATA_PIO4: return "PIO4";
|
2003-02-20 20:02:32 +00:00
|
|
|
|
case ATA_WDMA0: return "WDMA0";
|
|
|
|
|
case ATA_WDMA1: return "WDMA1";
|
2000-01-03 10:26:59 +00:00
|
|
|
|
case ATA_WDMA2: return "WDMA2";
|
2003-02-20 20:02:32 +00:00
|
|
|
|
case ATA_UDMA0: return "UDMA16";
|
|
|
|
|
case ATA_UDMA1: return "UDMA25";
|
2000-01-03 10:26:59 +00:00
|
|
|
|
case ATA_UDMA2: return "UDMA33";
|
2003-02-20 20:02:32 +00:00
|
|
|
|
case ATA_UDMA3: return "UDMA40";
|
2000-01-03 10:26:59 +00:00
|
|
|
|
case ATA_UDMA4: return "UDMA66";
|
2000-08-06 19:51:58 +00:00
|
|
|
|
case ATA_UDMA5: return "UDMA100";
|
2001-10-06 11:07:04 +00:00
|
|
|
|
case ATA_UDMA6: return "UDMA133";
|
2003-05-18 16:43:08 +00:00
|
|
|
|
case ATA_SA150: return "SATA150";
|
2005-08-12 16:54:11 +00:00
|
|
|
|
case ATA_SA300: return "SATA300";
|
2006-03-05 21:32:38 +00:00
|
|
|
|
case ATA_USB: return "USB";
|
|
|
|
|
case ATA_USB1: return "USB1";
|
|
|
|
|
case ATA_USB2: return "USB2";
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
default:
|
|
|
|
|
if (mode & ATA_DMA_MASK)
|
|
|
|
|
return "BIOSDMA";
|
|
|
|
|
else
|
|
|
|
|
return "BIOSPIO";
|
2000-01-03 10:26:59 +00:00
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
|
2000-02-18 20:57:33 +00:00
|
|
|
|
int
|
|
|
|
|
ata_pmode(struct ata_params *ap)
|
|
|
|
|
{
|
|
|
|
|
if (ap->atavalid & ATA_FLAG_64_70) {
|
2003-02-20 20:02:32 +00:00
|
|
|
|
if (ap->apiomodes & 0x02)
|
|
|
|
|
return ATA_PIO4;
|
2004-05-20 14:49:12 +00:00
|
|
|
|
if (ap->apiomodes & 0x01)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_PIO3;
|
2004-05-20 14:49:12 +00:00
|
|
|
|
}
|
2003-09-08 08:30:43 +00:00
|
|
|
|
if (ap->mwdmamodes & 0x04)
|
|
|
|
|
return ATA_PIO4;
|
|
|
|
|
if (ap->mwdmamodes & 0x02)
|
|
|
|
|
return ATA_PIO3;
|
|
|
|
|
if (ap->mwdmamodes & 0x01)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_PIO2;
|
2003-09-08 08:30:43 +00:00
|
|
|
|
if ((ap->retired_piomode & ATA_RETIRED_PIO_MASK) == 0x200)
|
|
|
|
|
return ATA_PIO2;
|
|
|
|
|
if ((ap->retired_piomode & ATA_RETIRED_PIO_MASK) == 0x100)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_PIO1;
|
2003-09-08 08:30:43 +00:00
|
|
|
|
if ((ap->retired_piomode & ATA_RETIRED_PIO_MASK) == 0x000)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_PIO0;
|
2004-05-20 14:49:12 +00:00
|
|
|
|
return ATA_PIO0;
|
|
|
|
|
}
|
2000-02-18 20:57:33 +00:00
|
|
|
|
|
|
|
|
|
int
|
|
|
|
|
ata_wmode(struct ata_params *ap)
|
|
|
|
|
{
|
2001-10-06 11:07:04 +00:00
|
|
|
|
if (ap->mwdmamodes & 0x04)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_WDMA2;
|
2001-10-06 11:07:04 +00:00
|
|
|
|
if (ap->mwdmamodes & 0x02)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_WDMA1;
|
2001-10-06 11:07:04 +00:00
|
|
|
|
if (ap->mwdmamodes & 0x01)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_WDMA0;
|
2000-02-18 20:57:33 +00:00
|
|
|
|
return -1;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
int
|
|
|
|
|
ata_umode(struct ata_params *ap)
|
|
|
|
|
{
|
|
|
|
|
if (ap->atavalid & ATA_FLAG_88) {
|
2001-10-06 11:07:04 +00:00
|
|
|
|
if (ap->udmamodes & 0x40)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_UDMA6;
|
2000-08-06 19:51:58 +00:00
|
|
|
|
if (ap->udmamodes & 0x20)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_UDMA5;
|
2000-02-18 20:57:33 +00:00
|
|
|
|
if (ap->udmamodes & 0x10)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_UDMA4;
|
2000-02-18 20:57:33 +00:00
|
|
|
|
if (ap->udmamodes & 0x08)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_UDMA3;
|
2000-02-18 20:57:33 +00:00
|
|
|
|
if (ap->udmamodes & 0x04)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_UDMA2;
|
2000-02-18 20:57:33 +00:00
|
|
|
|
if (ap->udmamodes & 0x02)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_UDMA1;
|
2000-02-18 20:57:33 +00:00
|
|
|
|
if (ap->udmamodes & 0x01)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
return ATA_UDMA0;
|
2000-02-18 20:57:33 +00:00
|
|
|
|
}
|
|
|
|
|
return -1;
|
|
|
|
|
}
|
|
|
|
|
|
2003-02-20 20:02:32 +00:00
|
|
|
|
int
|
2005-04-30 16:22:07 +00:00
|
|
|
|
ata_limit_mode(device_t dev, int mode, int maxmode)
|
2003-02-20 20:02:32 +00:00
|
|
|
|
{
|
2005-04-30 16:22:07 +00:00
|
|
|
|
struct ata_device *atadev = device_get_softc(dev);
|
|
|
|
|
|
2003-02-20 20:02:32 +00:00
|
|
|
|
if (maxmode && mode > maxmode)
|
|
|
|
|
mode = maxmode;
|
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
if (mode >= ATA_UDMA0 && ata_umode(&atadev->param) > 0)
|
|
|
|
|
return min(mode, ata_umode(&atadev->param));
|
2003-02-20 20:02:32 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
if (mode >= ATA_WDMA0 && ata_wmode(&atadev->param) > 0)
|
|
|
|
|
return min(mode, ata_wmode(&atadev->param));
|
2003-02-20 20:02:32 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
if (mode > ata_pmode(&atadev->param))
|
|
|
|
|
return min(mode, ata_pmode(&atadev->param));
|
2003-02-20 20:02:32 +00:00
|
|
|
|
|
|
|
|
|
return mode;
|
|
|
|
|
}
|
|
|
|
|
|
2005-04-29 11:30:03 +00:00
|
|
|
|
static void
|
|
|
|
|
bswap(int8_t *buf, int len)
|
|
|
|
|
{
|
|
|
|
|
u_int16_t *ptr = (u_int16_t*)(buf + len);
|
|
|
|
|
|
|
|
|
|
while (--ptr >= (u_int16_t*)buf)
|
|
|
|
|
*ptr = ntohs(*ptr);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static void
|
|
|
|
|
btrim(int8_t *buf, int len)
|
|
|
|
|
{
|
|
|
|
|
int8_t *ptr;
|
|
|
|
|
|
|
|
|
|
for (ptr = buf; ptr < buf+len; ++ptr)
|
|
|
|
|
if (!*ptr || *ptr == '_')
|
|
|
|
|
*ptr = ' ';
|
|
|
|
|
for (ptr = buf + len - 1; ptr >= buf && *ptr == ' '; --ptr)
|
|
|
|
|
*ptr = 0;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static void
|
|
|
|
|
bpack(int8_t *src, int8_t *dst, int len)
|
|
|
|
|
{
|
|
|
|
|
int i, j, blank;
|
|
|
|
|
|
|
|
|
|
for (i = j = blank = 0 ; i < len; i++) {
|
|
|
|
|
if (blank && src[i] == ' ') continue;
|
|
|
|
|
if (blank && src[i] != ' ') {
|
|
|
|
|
dst[j++] = src[i];
|
|
|
|
|
blank = 0;
|
|
|
|
|
continue;
|
|
|
|
|
}
|
|
|
|
|
if (src[i] == ' ') {
|
|
|
|
|
blank = 1;
|
|
|
|
|
if (i == 0)
|
|
|
|
|
continue;
|
|
|
|
|
}
|
|
|
|
|
dst[j++] = src[i];
|
|
|
|
|
}
|
|
|
|
|
if (j < len)
|
|
|
|
|
dst[j] = 0x00;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
/*
|
|
|
|
|
* module handeling
|
|
|
|
|
*/
|
|
|
|
|
static int
|
|
|
|
|
ata_module_event_handler(module_t mod, int what, void *arg)
|
2000-02-18 20:57:33 +00:00
|
|
|
|
{
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
static struct cdev *atacdev;
|
|
|
|
|
|
|
|
|
|
switch (what) {
|
|
|
|
|
case MOD_LOAD:
|
|
|
|
|
/* register controlling device */
|
|
|
|
|
atacdev = make_dev(&ata_cdevsw, 0, UID_ROOT, GID_OPERATOR, 0600, "ata");
|
|
|
|
|
|
|
|
|
|
if (cold) {
|
|
|
|
|
/* register boot attach to be run when interrupts are enabled */
|
|
|
|
|
if (!(ata_delayed_attach = (struct intr_config_hook *)
|
|
|
|
|
malloc(sizeof(struct intr_config_hook),
|
|
|
|
|
M_TEMP, M_NOWAIT | M_ZERO))) {
|
|
|
|
|
printf("ata: malloc of delayed attach hook failed\n");
|
|
|
|
|
return EIO;
|
|
|
|
|
}
|
|
|
|
|
ata_delayed_attach->ich_func = (void*)ata_boot_attach;
|
|
|
|
|
if (config_intrhook_establish(ata_delayed_attach) != 0) {
|
|
|
|
|
printf("ata: config_intrhook_establish failed\n");
|
|
|
|
|
free(ata_delayed_attach, M_TEMP);
|
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
|
|
case MOD_UNLOAD:
|
|
|
|
|
/* deregister controlling device */
|
|
|
|
|
destroy_dev(atacdev);
|
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
|
|
default:
|
|
|
|
|
return EOPNOTSUPP;
|
2000-02-18 20:57:33 +00:00
|
|
|
|
}
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
}
|
2004-01-11 22:08:34 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
static moduledata_t ata_moduledata = { "ata", ata_module_event_handler, NULL };
|
|
|
|
|
DECLARE_MODULE(ata, ata_moduledata, SI_SUB_CONFIGURE, SI_ORDER_SECOND);
|
|
|
|
|
MODULE_VERSION(ata, 1);
|
2003-05-02 13:47:44 +00:00
|
|
|
|
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
static void
|
|
|
|
|
ata_init(void)
|
|
|
|
|
{
|
2005-04-18 16:01:56 +00:00
|
|
|
|
ata_request_zone = uma_zcreate("ata_request", sizeof(struct ata_request),
|
|
|
|
|
NULL, NULL, NULL, NULL, 0, 0);
|
|
|
|
|
ata_composite_zone = uma_zcreate("ata_composite",
|
2005-04-30 16:22:07 +00:00
|
|
|
|
sizeof(struct ata_composite),
|
|
|
|
|
NULL, NULL, NULL, NULL, 0, 0);
|
2000-02-18 20:57:33 +00:00
|
|
|
|
}
|
2005-04-18 16:01:56 +00:00
|
|
|
|
SYSINIT(ata_register, SI_SUB_DRIVERS, SI_ORDER_SECOND, ata_init, NULL);
|
This is the much rumoured ATA mkIII update that I've been working on.
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
2005-03-30 12:03:40 +00:00
|
|
|
|
|
2005-04-18 16:01:56 +00:00
|
|
|
|
static void
|
|
|
|
|
ata_uninit(void)
|
|
|
|
|
{
|
|
|
|
|
uma_zdestroy(ata_composite_zone);
|
|
|
|
|
uma_zdestroy(ata_request_zone);
|
|
|
|
|
}
|
|
|
|
|
SYSUNINIT(ata_unregister, SI_SUB_DRIVERS, SI_ORDER_SECOND, ata_uninit, NULL);
|