use of the extsts field in DMA descriptors. We need this to tell the chip
to calculate TCP/IP checksums in hardware on a per-packet basis.
- Fix the unions in DMA descriptor structures. Breakage on alpha led
me to realize I'd done it wrong the first time.
that device add/remove will work without usbd running. usbd is still
used for execing stuff, but that is all now. Ideally it could be replaced
by a devd some day. Until now, usbd had to be running so that the
USB_DISCOVER ioctl could be called to walk the tree when an attachment
status change was noticed.
Among the changes:
- when a detach happens, remove any pending 'attach' messages or the system
suffers from whiplash from exec moused / kill moused loops if you do lots
of attach/detach and later start usbd.
- tweaks related to kthread differences
- disable the select handler for the old interface (never return success).
I have not removed it yet or old usbd's will abort. That can get removed
later once usbd is cleaned up and things have stabilized for a few weeks.
- get Giant in the kthread.
- a couple of minor potential bug fixes (usb_nevents vs malloc failure etc)
Pre-approved by: n_hibma (ages and ages ago)
ep driver. The rest of the patch will wait until I can put the time
into it to get it righter than the kludge it is.
This protects us against card eject problems at all times,e xecpt when
we're in the epintr ISR.
I think bde even reviewed it once.
Also, change the name of ActionTEC pat to more generic Lucent Kermit
chip. Add stub for Xircom card. Add cardbus attachment too.
compliant. All the variable definitions and function names are
reasonably consistent, and the functions which should be static (i.e.,
all of them) are. Other assorted fixes were made. The majority of
the delta is indentation fixes.
Partially reviewed by: bde
can be made userland-visible as <dev/ic/...>. Also, those files are
not supposed to contain any bus-specific details at all, so placing
them under .../isa/ has been a misnomer from the beginning.
The files in src/sys/dev/ic/ have been repo-copied from their old
location (this commit is a forced null commit there to record this
message).
The 3C509-TX card apparently had a slightly different version of the
chip, and has problems when this register is set. The problem does
not appear on the 3C509{BC} cards, but since only the fxp driver needs
specific bits set, conditionalize on that.
all alphas with devices behind ppb's. I'm working on a better solution now.
Note that all alphas that use per-platform interrupt mapping are broken
again (as they have been for several months)
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
this works on cs4630 chips, and should implement the clkrun hack for
thinkpads- this will display diagnostic messages when triggered until its
correctness is established.
UDP checksums too, not just IP. The chip only tells us if the checksum
is ok, it does not give us a copy of the partial checksum for later
processing. We have to deal with this the right way, but we can deal
with it.
- Use __func__ instead of __FUNCTION.
- Support power-off to S3 or S5 (takawata)
- Enable ACPI debugging earlier (with a sysinit)
- Fix a deadlock in the EC code (takawata)
- Improve arithmetic and reduce the risk of spurious wakeup in
AcpiOsSleep.
- Add AcpiOsGetThreadId.
- Simplify mutex code (still disabled).
----
Make a device for each ISP- really usable only with devfs and add an ioctl
entry point (this can be used to (re)set debug levels, reset the HBA,
rescan the fabric, issue lips, etc).
----
Add in a kernel thread for Fibre Channel cards. The purpose of this
thread is to be woken up to clean up after Fibre Channel events
block things. Basically, any FC event that casts doubt on the
location or identify of FC devices blocks the queues. When, and
if, we get the PORT DATABASE CHANGED or NAME SERVER DATABASE CHANGED
async event, we activate the kthread which will then, in full thread
context, re-evaluate the local loop and/or the fabric. When it's
satisfied that things are stable, it can then release the blocked
queues and let commands flow again.
The prior mechanism was a lazy evaluation. That is, the next command
to come down the pipe after change events would pay the full price
for re-evaluation. And if this was done off of a softcall, it really
could hang up the system.
These changes brings the FreeBSD port more in line with the Solaris,
Linux and NetBSD ports. It also, more importantly, gets us being
more proactive about topology changes which could then be reflected
upwards to CAM so that the periph driver can be informed sooner
rather than later when things arrive or depart.
---
Add in the (correct) usage of locking macros- we now have lock transition
macros which allow us to transition from holding the CAM lock (Giant)
and grabbing the softc lock and vice versa. Switch over to having this
HBA do real locking. Some folks claim this won't be a win. They're right.
But you have to start somewhere, and this will begin to teach us how
to DTRT for HBAs, etc.
--
Start putting in prototype 2300 support. Add back in LIP
and Loop Reset as async events that each platform will handle.
Add in another int_bogus instrumentation point.
Do some more substantial target mode cleanups.
MFC after: 8 weeks
breakage:
- call PCIB_ROUTE_INTERRUPT() regardless of how valid the intline looks.
Some alphas leave garbage in the intline and leave the intr mapping
to OS platform support routines that map slots/buses to intlines
- Down in the alpha pci code, first try platform.pci_intr_route() and
if it doesn't exist or returns garbage, just read the intline out of
config space.
tested on AS500 (garbage in intline) and UP1000 (PC-like, intline is valid)
Note that a nice little hack like the APIC_IO section of pci_cfgregread()
is not workable. This is because the calling interface for
alpha_pci_route_interrupt() requires us to figure out the bus/slot/etc
from a device_t. At pci_read_device() time, we don't have a device_t
for the bus/slot/func in question.
instead of using two malloced arrays for storing channel lists, use an
slist. convert the sndstat device to use sbufs and optionally provide more
detail about channel state.
vchans are software mixed playback channels. they are not enabled by this
commit. they use the feeder infrastructure to emulate normal playback
channels in a manner transparent to applications, whilst providing as many
channels are desired, especially suitable for devices with only one hardware
playback channel. in the future they will provide additional features.
those wishing to test this functionality will need to add vchan.c to
sys/conf/files and use 'sysctl -w hw.snd.pcm0.vchans' to enable it.
blocksize and auto-rate selection are not yet supported.
SC_DEV isn't NULL; if it is, evaluate to NULL and don't dereference
NULL. Callers of VIRTUAL_TTY must already check for the result being
NULL since si_tty can be NULL, so this should be safe.
This fixes a panic when trying to switch to a different vty in an
environment such as userconfig (-c option to the kernel).
PR: 26508
despite the fact that most people want to set exactly the same settings
regardless of which card they have. It has been repeatidly suggested
that this configuration should be done via ifconfig. This patch
implements the required functionality in ifconfig and add support to the
wi and an drivers. It also provides partial, untested support for the
awi driver.
PR: 25577
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
by both OLDCARD and NEWCARD.
# didn't make the tables the same because oldcard supports more devices than
# newcard and newcard's 16-bit stuff needs some work.
the built-in 1000baseX interface in the Level 1 LXT1001 chip. The Level 1
PHY comes up with the isolate bit in the control register set by default,
but it also has the autonegotiate bit set. When you tell the xmphy driver
to select IFM_AUTO mode, it sees that the autoneg bit is already on, and
thus doesn't bother updating the control register. However this means that
the isolate bit is never turned off (unless you manually select 1000baseSX
full or half duplex mode, which does result in the control register being
modified and the ISO bit being turned off).
This subtle and unusual behavioral difference stopped me from being able
to receive packets on the SMC9462TX card for several days, since isolating
the PHY disconnects it from the MAC's data interface. The fix is to omit
the 'is the autoneg big set?' test, since it doesn't really provide much
of an optimization anyway.
This commit also updates the xmphy driver to support the Jato/Level 1
internal PHY. (I'm not sure how Jato Technologies is related to Level 1:
all I know is the OUI from the PHY ID registers maps to Jato in the OUI
database.) This will be used once I add the if_lge driver to support
the LXT10010 chip.
requiring fewer header files for userland programs.
Remove the gross debug device/non-debug device hack used to recognize
whether the kernel module was in sync with the userland module.
compiled with debug support. This can be used by userland programs to
recognize which ioctls the module supports.
As a result, remove the gross debug device/non-debug device hack used
to recognize whether the kernel module was in sync with the userland
module.
Replace explicit references to major/minor numbers of vinum
superdevice with the VINUM_SUPERDEV macro written for that purpose.
needs instead of relying on idiosyncratic hacks in the tty subsystem.
Also add module code since this can now be compiled as a module.
Silence by: -hackers, -audit
gets incremented every time the kernel-userland interface changes.
This enables vinum(8) to check for the correct kernel version and to
produce a useful message if it doesn't match.
Requested by: Too many to count.
Move the definitions of struct drive, sd, plex and volume to
vinumobj.h.
Add a new debug flag, DEBUG_LOCKREQS, which logs only lock requests.
with more than one plex, the data will be accessed
multiple times. During this time, userland code could
potentially modify the buffer, thus causing data
corruption. In the case of a multi-plexed volume this
might be cosmetic, but in the case of a RAID-[45] plex it
can cause severe data corruption which only becomes
evident after a drive failure. Avoid this situation by
making a copy of the data buffer before using it.
Note that this solution does not guarantee any particular
content of the buffer, just that it remains unchanged for
the duration of the request.
Suggested by: alfred
Use this instead of DEBUG_LASTREQS to decide whether to log lock
requests.
MFS:
vinumlock: Catch a potential race condition where one process is
waiting for a lock, and between the time it is woken and
it retries the lock, another process gets it and places it
in the first entry in the table.
This problem has not been observed, but it's possible, and
it's easy enough to fix.
Submitted by: tegge
vinumunlock: Catch a real bug capable of hanging a system. When
releasing a lock, vinumunlock() called wakeup_one. This
caused wakeups to sometimes get lost. After due
consideration, we think that this is due to the fact that
you can't guarantee that some other process is also
waiting on the same address. This makes wakeup_one a
very dangerous function to use.
Requested by: bde
Add retryerrors keyword.
vinum_scandisk: Print a different message if an inadvertent start
command did not find any additional drives. The previous message "no
drives found" confused and worried many people.
MFS:
vinum_open: Recognize Mylex devices as storage devices.
In case of error, check the VF_RETRYERRORS flag in the subdisk and
don't take the subdisk down if it's set, just retry the I/O.
Requested by: peter
If the buffer has been copied (XFR_COPYBUF), release the copied
buffer when the I/O completes.
Suggested by: alfred
Desired by: bde
This commit is the first of a general cleanup of the header files..
It won't be enough to make bde happy.
Move debug definitions from vinumhdr.h.
Create a new struct rangelockinfo. In revision 1.21 of vinumlock.c,
the plex info was removed from struct rangelock, since it wasn't
needed there. It *is* needed for trace information, however, so use
struct rangelockinfo for that.
vm_mtx does not recurse and is required for most low level
vm operations.
faults can not be taken without holding Giant.
Memory subsystems can now call the base page allocators safely.
Almost all atomic ops were removed as they are covered under the
vm mutex.
Alpha and ia64 now need to catch up to i386's trap handlers.
FFS and NFS have been tested, other filesystems will need minor
changes (grabbing the vm lock when twiddling page properties).
Reviewed (partially) by: jake, jhb
copies out the current contents of the video buffer for a syscons terminal,
providing a snapshot of the text and attributes.
Based heavily on work originally submitted by Joel Holveck <joelh@gnu.org>
for 2.2.x almost 30 months ago, which I cleaned up a little, and forward
ported to -current.
See also the usr.bin/scrshot utility.
Pro and Raylink cards with version 5 firmware. Only infra-structure
mode has been tested. Specific changes for this feature are:
o Add RFC1042 encapsulation of IP datagrams
o Add authentication and association
o Decode of the beacon (although not used)
Other changes have been made:
o Pass command completion status to *_done (in place for
adding proper error recovery)
o Move a couple of state variables into the current
network parameters structure. This is in prep. for
dealing with roaming.
MFC after: 1 week
be unions with enough padding to make sure they always end up being
a multiple of 8 bytes in size, since the 83820/83821 chips require
descriptors to be aligned on 64-bit boundaries. I happened to get it
right for the 32-bit descriptor/x86 case, but botched everything else.
Things should work properle on 32-bit/64-bit platforms now.
Note that the 64-bit descriptor format isn't being used currently.
ahc_pci.c:
Prepare for making ahc a module by adding module dependency
and version info.
aic7770.c:
Remove linux header ifdefs. The headers are handled differently
in Linux where local includes (those using "'s instead of <>'s)
are allowed.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
aic7xxx.c:
Remove linux header ifdefs.
current->curr to avoid Linux's use of current as a
#define for the current task on some architectures.
Add a helper function, ahc_assert_atn(), for use in
message phases we handle manually. This hides the fact
that U160 chips with the expected phase matching disabled
need to have SCSISIGO updated differently.
if (ahc_check_residual(scb) != 0)
ahc_calc_residual(scb);
else
ahc_set_residual(scb, 0);
becomes:
ahc_update_residual(scb);
Modify scsi parity error (or CRC error) handling to
reflect expected phase being disabled on U160 chips.
Move SELTO handling above BUSFREE handling so we can
use the new busfree interrupt behavior on U160 chips.
In ahc_build_transfer_msg() filter the period and ppr_options
prior to deciding whether a PPR message is required.
ppr_options may be forced to zero which will effect our
decision.
Correct a long standing but latent bug in ahc_find_syncrate().
We could choose a DT only rate even though DT transfers were
disabled. In the CAM environment this was unlikely as CAM
filters our rate to a non-DT value if the device does not
support such rates.
When displaing controller characteristics, include the
speed of the chip. This way we can modify the transfer
speed based on optional features that are enabled/disabled
in a particular application.
Add support for switching from fully blown tagged queing
to just using simple queue tags should the device reject
an ordered tag.
Remove per-target "current" disconnect and tag queuing
enable flags. These should be per-device and are not
referenced internally be the driver, so we let the OSM
track this state if it needs to.
Use SCSI-3 message terminology.
aic7xxx.h:
The real 7850 does not support Ultra modes, but there are
several cards that use the generic 7850 PCI ID even though
they are using an Ultra capable chip (7859/7860). We start
out with the AHC_ULTRA feature set and then check the
DEVSTATUS register to determine if the capability is really
present.
current -> curr
ahc_calc_residual() is no longer static allowing it to
be called from ahc_update_residual() in aic7xxx_inline.h.
Update some serial eeprom definitions for the latest
BIOS versions.
aic7xxx.reg:
Add a combined DATA_PHASE mask to the SCSIPHASE register
definition to simplify some sequencer code.
aic7xxx.seq:
Take advantage of some performance features available only
on the U160 chips. The auto-ack feature allows us to ack
data-in phases up to the data-fifo size while the sequencer
is still setting up the DMA engine. This greatly reduces
read transfer latency and simplifies testing for transfer
complete (check SCSIEN only). We also disable the expected
phase feature, and enable the new bus free interrupt behavior,
to avoid a few instructions.
Re-arrange the Ultra2+ data phase handling to allow us to
do more work in parallel with the data fifo flushing on a
read.
On an SDTR, ack the message immediately so the target can
prepare the next phase or message byte in parallel with
our work to honor the message.
aic7xxx_93cx6.c:
Remove linux header ifdefs.
aic7xxx_freebsd.c:
current -> curr
Add a module event handler.
Handle tag downgrades in our ahc_send_async() handler.
We won't be able to downgrade to "basic queuing" until
CAM is made aware of this queuing type.
aic7xxx_freebsd.h:
Include cleanups.
Define offsetof if required.
Correct a few comments.
Update prototype of ahc_send_async().
aic7xxx_inline.h:
Implement ahc_update_residual().
aic7xxx_pci.c:
Remove linux header ifdefs.
Correct a few product strings.
Enable several U160 performance enhancing features.
Modify Ultra capability determination so we will enable
Ultra speeds on devices with a 7850 PCI id that happen
to really be a 7859 or 7860.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
of " &= ". Also change the MII PHY device mask to check the correct bits.
Cookie to: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
Pointy hat to: me
. FD_CLRERR clears the error counter, thus re-enables kernel error
printf()s,
. FD_GSTAT obtains the last FDC operation state, if any,
. FDOPT_NOERRLOG (temporarily) turns off kernel printf() floppy
error logging,
. FDOPT_NOERROR makes the kernel ignore an FDC error, thus can
enable the transfer of an erroneous sector to the user application
All options are being cleared on (last) close.
Prime consumer of the last features will be fdread(1), to be committed
shortly.
(FD_CLRERR should be wired into fdcontrol(8), but then fdcontrol(8)
needs a major rewrite anyway.)
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
a LinkSys card here in the office where reading the station address
fails the first time, but works find afterwards. Without this, the
probe fails. I don't think this will negatively impact any existing
cards, but I want to confirm this before MFC'ing.
we need to delete the info from the list as well as zero out the res
pointer we saved in the code.
Also made a few style(9) changes while I was at it. Don't use if
(ptr) or if (!ptr), but compare against NULL. Compare against NULL
rather than 0. Don't have useless blocks.
There are likely other problems as well, but at least the wi based
wireless card with memory listed in its cis doesn't panic the system
when the card is inserted.
use TAILQ macros. The sk_attach_xmac() routine calls sk_init_xmac()
before doing the transceiver probe, but *before* ether_ifattach()
is called. This causes sk_init_xmac() to call sk_setmulti(), which
tries to do a TAILQ_FOREACH(), which it can't do because ether_ifattach()
hasn't done a TAILQ_INIT() yet. This causes a NULL pointer dereference
and panic in sk_setmulti() at driver load/initialization time.
Fixed by calling ether_ifattach() before the MII probe.
The code in RELENG_4 still uses the old way of enumerating the
multicast list and doesn't have this problem. Yet.
Reduce the verbose memory map setup reports and work with pccardd to
set the common memory map up.
Use enumeration values for CARD_SET_RES_FLAGS.
Use DELAY when spinning waiting for the card to come free instead of a loop.
MFC: after 1 week
Tidy up includes, credit Slawa Olhovchenkov, John Prince and Eric Hernes
for their efforts and add a couple of missing parenthesis around return
expressions.
- Rework of twe_report_request to use the command status value rather
than the flags register. (Joel Jacobson @ 3ware)
- Update to match some changes in -current vs. stable.
MFC in: 1 week
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
other "system" header files.
Also help the deprecation of lockmgr.h by making it a sub-include of
sys/lock.h and removing sys/lockmgr.h form kernel .c files.
Sort sys/*.h includes where possible in affected files.
OK'ed by: bde (with reservations)
The constant I was using was correct, but I mislabeled it as 256K when
it should have been 512K. This doesn't actually change the code, but
it clarifies things somewhat.
Submitted by: Chuck Cranor <chuck@research.att.com>
