- Fix style for A3N and for a comment
Submitted by: Akira Funahashi <funa@funa.org>
Tested by: Marcin Nowak <marcin.nowak@simplusnet.pl>,
Diego Sardina <diego.sardina@gmx.com>
PR: kern/128634
the ATA status register with a 4-byte read request. This updates it, and
subsequent 1-byte reads will return the correct result.
This commit adds a hack to do this, which is currently ifdef'd powerpc,
although Linux and Darwin do this unconditionally on all platforms.
provided, for example, on the PowerPC 970 (G5), as well as on related CPUs
like the POWER3 and POWER4.
This also adds support for various built-in hardware found on Apple G5
hardware (e.g. the IBM CPC925 northbridge).
Reviewed by: grehan
The DIROUT bit difference between the 19 and 22 is annoying. We can
set both bits on both parts without ill effect. Use this trick to
simplify the code.
The DELAYS in the MII bus bit-bang code for the DL100xx parts aren't
needed. Eliminate them.
packet data. However, the AX88190A moves this on-chip and reduces it
to the more traditional 16k from 16k-32k. The AX88790 follows the
'190A. Probe memory above 32k to see which flavor of the '190 we have
and use the extra memory if we have it.
Eliminate the kludgy read eeprom for the ID code. It really is just a
memory read at location 0x400, so just use that instead. Makes the
code easier to understand as well as eliminates some magic numbers.
ed cards. There's a number of minor nits in a lot of the PHYs on the
PC Cards that use the Axis AX88190 or DLink DL10019 and DL10022 chips.
Forcing the autonegotiation doesn't seem to cause problems on the
cards that have sane PHYs, but makes several cards I have work without
further workarounds.
I'm not 100% sure that kicking the PHY and resetting them is the right
thing to do on the media change callback. Other NICs seem to need
this and do similar things.
only for mic-type inputs. This gives better chances to use it.
Change default configuration for some AD1986A codec based ASUS boards,
use it also for ASUS P5PL2 board. This makes front mic preamplifier working.
Tested by: Vadim Frolov <frolov@frolov.ck.ua>
o Don't run through the register initialization in the read mac routine
for the AX88x90. It duplicates other stuff that we do.
o Eliminate the 10ms delay after we reset the AX88x90. We already wait for
the appropriate bits to indicate reset is done.
a device specific DMA tag. On amd64 it could exhaust all of bounce
pages when bus_dma_tag_create(9) is called at malo_pci_attach() then as
result in next turn it returns ENOMEM. This fix a attach fail on amd64.
Pointed by: yongari
Tested by: dchagin
MFC after: 3 days
It seems that RTL8168D and RTL8102EL requires additional settle
time to complete RL_PHYAR register write. Accessing RL_PHYAR
register right after the write causes errors for subsequent PHY
register accesses.
Tested by: george at luckytele dot com,
Steve Wills < STEVE at stevenwills dot com >
don't have one of the clock cycles (the turn cycle) that the AX88x90
chips have. Make this conditional. But this seems totally crazy and
can't possibly be right. Commit the fix for the moment until I can
explore this mystery more deeply.
On the plus side, the DL10022-based cards I have (D-Link DEF-670TXD
and SMC8040TX) work after this fix.
Add ch_suspend/ch_resume methods for PCI controllers and implement them
for AHCI. Refactor AHCI channel initialization according to it.
Fix Port Multipliers operation. It is far from perfect yet, but works now.
Tested with JMicron JMB363 AHCI + SiI 3726 PMP pair.
Previous version was also tested with SiI 4726 PMP.
Hardware sponsored by: Vitsch Electronics / VEHosting.nl
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o Introduce new chip_type AX88790. There's a few places we need to know the
exact chip for workaronds.
o Explain the AX88190 workaround for the ISR bits being stuck, and don't
apply them to the AX88790. The datasheet says the bits are fixed, and
experience confirms.
o Fix mii bit-bang read code to read and discard the 'floating' bit.
o Remove empty ed_pccard_ax88x90_mii_reset routine
o Report error from mii_phy_probe
o Don't use ed_probe_Novel_generic for ax88x90 chips. It puts them into
an odd state sometimes. Instead, use a more stream-lined version that
avoids the trouble spots. This was copied and tweaked from the original.
o Move chip reset into its own routine.
o Minor code optimiation on getting MAC address
o Add code for coping with AX88790 cards that are in power down state and
need to be kicked before the PHY registers for the internal phy read right.
o Remove ugly cap of PHYs at 17.
o For AX88790, we need to set a special bit for accessig phy 16 (the internal
phy) and clear it for all others according to a chip erratum.
o streamline the bit-bang code for AX88x90: the delays aren't needed according
to the datasheet timing diagrams and also the Linux driver
o Fix minor bit definition for direction bit.
o Generally: Some comments reformatted
o Only try the toshiba probe on cards labelled as toshiba
# From another Akihabara card (this one from a few years ago from a
# friend in Japan). Fix the Corega FEther II PCC-TXD. This one is
# still on sale new, as of a few weeks ago. should fix all other AX88x90
# based cards, but I have some testing left to finish on my collection...
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
It seems that some revision of controller hang while accessing
the VPD. Because VPD access routine are unused, nuke it.
o Let TWSI reload EEPROM if VPD capability is detected. Reloading
EEPROM will also set ethernet address so age(4) now reads AGE_PAR0
and AGE_PAR1 register to get ethernet address. This removes a lot
of hack and enhance readability a lot.
o Double PHY reset timeout as it takes more time to take PHY out of
power-saving state.
o Explicitly check power-saving state by checking undocumented PHY
registers. If link is not up, poke undocumented registers to take
PHY out of power-saving state. This is the same way what Linux
does. On resume, make sure to wake up PHY.
o Don't rely on auto-clearing feature of master reset bit, just wait
1ms and check idle status of MAC.
o Add PCI device revision information in bootverbose mode.
This should fix occasional controller hang in device attach phase.
Reported by: barbara < barbara.xxx1975 at libero DOT it >
Tested by: barbara < barbara.xxx1975 at libero DOT it >
up) rather than amount + 1 / 2, which is the same as amount, or 2x too
many words which leads to data corruption.
# This fixes the sbdrop panics I was seeing with the Toshiba LANCT00A.
Toshiba PCETC ISA card, and even has the same board type code in the
card ID (0x14). So, for this card, call ed_probe_WD80x3_generic after
setting things up apropriately. This makes the card attach and kinda
work (I'm seeing panics in sbdrop). Since history has shown that the
WD80x3 probe routine is dangerous, only do it for this card. Also,
disable the memory range check to make sure it is an valid ISA memory.
I think that it is bogus, but I'm not 100% sure, for these cards.
I removed probing for the WD80x3 in 2005 when I added support for the
AX88x90 and DL100xx cards since none of my cards had ever matched it
and PAO3 removed it and none of the cards in their database died.
It is possible there are other quirks about this card too, since no
other open source OS supports it, or even claims to support it. But
it was a fun half hour hack...
driver. Not sure who sold it/rebadged it.
Add stub entries for Mitsubishi B8895 and Toshiba LANCT00A to the
driver with a comment that they don't work /* NG */.[*] These are
DP83902A based cards, which should work, but don't seem to. Likely
they are from the days before the ne2000 roamed the earth and use a
non-standard hookup (see if_ed_isa or if_ed_cbus for some examples).
Unless I happen to stumble into the right one, these may never work,
but I'm tired of omitting them from commits.
[*] The Japanese adopted OK from English, but also use NG for its
opposite.
rather than behind a seemingly accidental constant likely left over from one of
the related drivers which uses log levels rather than per-facility debugging
flags. This should get rid of contextless messages on the console for people
who have not set (or cleared the default) debugging flags.
packet. Linux, OpenBSD and our iwn(4) all do this. It also results in
a huge performance improvement (and the rejection of a fair number of
apparently-bad packets on receive) on my hardware.
o) Like the wpi(4) driver in OpenBSD, and like our iwn(4), also drop runt
packets.
o) Don't bother doing IFQ_POLL and then IFQ_DRV_DEQUEUE, just do
IFQ_DRV_DEQUEUE outright. This is more similar to how OpenBSD and our
iwn(4) work.
Reviewed by: sam
into acpi_cpu_startup() which is where all the other code to update this
global variable lives. This fixes a bug where cpu_cx_count was not updated
correctly if acpi_cpu_generic_cx_probe() returned early.
PR: kern/108581
Debugged by: Bruce Cran
Reviewed by: avg, njl, sepotvin
MFC after: 3 days
via the Linux tool.
- Add Linux shim to ipmi(4)
- Create a partitions file to linprocfs to make Linux fdisk see
disks. This file is dynamic so we can see disks come and go.
- Convert msdosfs to vfat in mtab since Linux uses that for
msdosfs.
- In the Linux mount path convert vfat passed in to msdosfs
so Linux mount works on FreeBSD. Note that tasting works
so that if da0 is a msdos file system
/compat/linux/bin/mount /dev/da0 /mnt
works.
- fix a 64it bug for l_off_t.
Grabing sh, mount, fdisk, df from Linux, creating a symlink of mtab to
/compat/linux/etc/mtab and then some careful unpacking of the Linux bmc
update tool and hacking makes it work on newer Dell boxes. Note, probably
if you can't figure out how to do this, then you probably shouldn't be
doing it :-)
When a vt switch occurs the irq handler is uninstalled. Interrupts
and the state tracking of what was enabled/disabled wasn't working
properly. This should resolve the reports of "slow windows" after a
vt switch, among other things. The radeon 2d driver seems to work a
bit more correctly than the Intel driver. With the Intel driver,
vblank interrupts will be enabled at system startup and will only
be disabled after an additional modeset (vt switch, dpms, randr event).
With this patch, I am able to run glxgears synced to vblank and
vt switch while it is running without ill effects.
MFC after: 3 days
prevent individual transactions from crossing a 4GB address boundary. Due
to bus_size_t type limitations, the driver uses a 2GB boundary in PAE
kernels.
Reviewed by: scottl
MFC after: 1 week
quirk requiring it to be enabled even when using MSI. This makes
the latter work again after r189285.
- Remove a comment which no longer applies since r190194.
filtering handle this. Introduce a new function msk_rxfilter that
handles Rx filter configuration and multicast setup as well as
promiscuous mode. This simplifies code a lot.
Promiscuous mode always have preference to any other Rx
filtering so don't disable the mode when ALLMULTI is set.
it is right for only a tiny fraction of these devices and this
wild-card entry is too broad.
# I run a kernel without this entry at all without ill effects...
The tick routine was not being restarted in the init_locked routine
which could resulted in loss of carrier when updating the MTU.
Submitted by: Navdeep Parhar at Chelsio
MFC after: 3 weeks
- If boot verbose, print asicrev, chiprev and bus type on attach.
- For PCI Express devices:
1) Adjust max read request size to 4Kbytes
2) Turn on FIFO_LONG_BURST in RDMA during bge_blockinit()
Though 1) does not seem to have much to do with the poor TX performance
observed on PCI Express bge(4), 2) does fix the problem. [1]
- Nuke the RX CPU self-diag, which prevents working cards from working
(Linux tg3 does not have this diag neither does OpenBSD's bge(4)).
The increasing of the firmware handshaking timeout to 20000 retries
done as part of the original commit isn't merged as way already have a
way higher BGE_TIMEOUT of 100000.
PR: 119361 [1]
Obtained from: tg3 via DragonflyBSD [1], DragonflyBSD
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
Workaround for buggy USB hardware not handling new SETUP packet before STATUS
stage is complete, this allows xfers to endpoint0 to return a short frame.
Submitted by: Hans Petter Selasky
Reported by: me
- Move tunable defines into usb_core.h and dependancy towards usb_defs.h
- Leave hardcoded defines in "usb_defs.h".
- Allow overriding all tunable defines.
- Add more customisable typedefs.
- Correct maximum device number.
Submitted by: Hans Petter Selasky
It seems I didn't fix this issue before committing teken to the tree. My
initial idea was to somehow add an error mechanism to instruct the video
driver author to increase T_NUMCOL when using very big terminals. It
turns out we have platforms where we have gigantic consoles on systems
like the Apple PowerMac G5, which means we crash there right now.
Just ignore tabstops placed beyond column 160. Just force tabs to be
placed on each 8 columns.
Reported by: nwhitehorn
supported with these pseudo-PHYs. The MIIF_NOLOOP flag currently triggers
nothing but hopefully will be respected by mii_phy_setmedia() later on.
- Don't add IFM_NONE as isolation isn't supported by these pseudo-PHYs.
- Use mii_phy_add_media() instead of mii_add_media() so the latter can
be eventually retired.
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
after vt switch or suspend. I can't really test this on Intel right now
but I think I've heard reports of it on radeon as well. I can't break
it on the radeon here.
MFC after: 3 days
o break out version-related code to simplify rev'ing the protocol
o add parameter validation macros so checks that appear multiple places
are consistent (and easy to change)
o add protocol version check when looking for a scan candidate
o improve scan debug output format
o rewrite beacon update handling to calculate a bitmask of changed values
and pass that down through the driver callback so drivers can optimize work
o do slot bounds check before use when parsing received beacons
or URB_FUNCTION_CLASS_xxx with HAL preemption lock that means it's
non-sleepable during USB requests though usb2_do_request() requires a
sleep so it needs to send queries to the default pipe without those
interfaces to avoid sleep.
Obtained from: Hideotshi Shimokawa
This update is based on comments from Hidetoshi.
Changeset 183550 removed the call to crom_load() in fw_busreset(). Restore
that call such that the Configuration ROM is valid.
Stash and update fwdev settings in fw_explore_node() so that negotiation
works again.
Fix regression issue in the USB file system interface.
- Use cdev_privdata pointer as indicator of correct file handle.
- Remove redundant FIFO opened flags.
Don't send ZLP at close for ulpt and uscanner devices as this causes some
models to stop working. This reverts back to the USB1 behaviour.
Submitted by: Hans Petter Selasky
This code is heavily inspired by Takanori Watanabe's experimental SMP patch
for i386 and large portion was shamelessly cut and pasted from Peter Wemm's
AP boot code.
implement CD input in hardware, while unconditional showing it confuse users.
Also it was made in the way that sometimes improper with present driver.
Add patch for ALC268 based Acer TM5320 to make headphones jack sensing work.
Default configuration defines two separate playback associations, which
current driver unable to trace properly due to order they are defined and
limited codec uniformity.
Submitted by: G. Mirov <g.mirov AT gmail.com>
