code.
# There is some question about whether this code is even relevant any
# longer (it dates back to prehistoric times, i.e. present in r1.1),
# especially on amd64.
Reviewed by: jhb
cpufreq_pre_change is called before the change, giving each driver a chance
to revoke the change. cpufreq_post_change provides the results of the
change (success or failure). cpufreq_levels_changed gives the unit number
of the cpufreq device whose number of available levels has changed. Hook
in all the drivers I could find that needed it.
* TSC: update TSC frequency value. When the available levels change, take the
highest possible level and notify the timecounter set_cputicker() of that
freq. This gets rid of the "calcru: runtime went backwards" messages.
* identcpu: updates the sysctl hw.clockrate value
* Profiling: if profiling is active when the clock changes, let the user
know the results may be inaccurate.
Reviewed by: bde, phk
MFC after: 1 month
handles when activating a resource via bus_activate_resource() rather than
doing some of the work in bus_alloc_resource() and some of it in
bus_activate_resource().
One note is that when using isa_alloc_resourcev() on PC-98, drivers now
need to just use bus_release_resource() without explicitly calling
bus_deactivate_resource() first. nyan@ has already fixed all of the PC-98
drivers.
address ranges used by local and I/O APICs in the system. Some systems
also reserve these ranges as system resources via either PnPBIOS or
ACPI, so this device currently attaches after acpi0 and legacy0 so that
the system resources are given precedence.
addresses corresponding to system RAM. On amd64 ram0 uses the SMAP
and claims all the type 1 SMAP regions. On i386 ram0 uses the
dump_avail[] array. Note that on i386 we have to ignore regions above
4G in PAE kernels since bus resources use longs.
GETATTRs being generated - one from lookup()/namei() and the other
from nfs_open() (for cto consistency). This change eliminates the
GETATTR in nfs_open() if an otw GETATTR was done from the namei()
path. Instead of extending the vop interface, we timestamp each attr
load, and use this to detect whether a GETATTR was done from namei()
for this syscall. Introduces a thread-local variable that counts the
syscalls made by the thread and uses <pid, tid, thread syscalls> as
the attrload timestamp. Thanks to jhb@ and peter@ for a discussion on
thread state that could be used as the timestamp with minimal overhead.
For example, during a buildworld more than half of the calls do not
generate an IPI because the only TLB entry invalidated is on the calling
processor. This revision pushes down the acquisition and release of
smp_ipi_mtx into smp_tlb_shootdown() and smp_targeted_tlb_shootdown() and
instead uses sched_pin() and sched_unpin() in pmap_invalidate_*() so that
thread migration doesn't lead to a missed TLB invalidation.
Reviewed by: jhb
MFC after: 3 weeks
Linux does not check file descriptor when MAP_ANONYMOUS is set.
This should fix recent LTP test regressions.
Reported by: Scot Hetzel (swhetzel at gmail dot com)
netchild
Rounding addr upwards to next 2M boundary in pmap_growkernel() could
cause addr to become 0, resulting in an early return without populating
the last PDE.
Reported and tested by: kris
Suggested by: alc
MFC after: 1 week
- PROT_READ, PROT_WRITE, or PROT_EXEC implies PROT_READ and PROT_EXEC.
Linux/ia64's i386 emulation layer does this and it complies with Linux
header files. This fixes mmap05 LTP test case on amd64.
- Do not adjust stack size when failure has occurred.
- Synchronize i386 mmap/mprotect with amd64.
partitioning class that supports multiple schemes. Current
schemes supported are APM (Apple Partition Map) and GPT.
Change all GEOM_APPLE anf GEOM_GPT options into GEOM_PART_APM
and GEOM_PART_GPT (resp).
The ctlreq interface supports verbs to create and destroy
partitioning schemes on a disk; to add, delete and modify
partitions; and to commit or undo changes made.
variable to avoid invalid constraints in dead code. Use an array of
u_char's (inside a struct) instead of a char/short/int/long variable so
that the variable and its accesses can be spelled in the same way in all
cases and code doesn't need to be cloned just to hold the spelling
differences.
Fixed strict-aliasing errors in PCPU_SET() and in the amd64 PCPU_GET().
Cast to (void *) as in rev.1.37 of the i386 version where the errors
were fixed for the i386 PCPU_GET() only. It would be more correct to
copy to and from the temp. variable using memcpy(), but then an
ifdef tangle would be required to ensure using the builtin memcpy().
We depend on fairly aggressive optimization to put the temp. variable
only in a register despite it being copied using
*(type *)(void *)&anothertype and could depend on this when using
memcpy() too. This seems to work right even for -O0, but the -O0 case
has not been completely tested.
This change gives identical object code for all object files in LINT
on amd64 (except for one file with a __TIME__ stamp). For LINT on
i386 it gives unimportant differences in instruction order and padding
in a few object files. This was only tested for -O.
This change (actually a previous version of it) gives the following
reductions in the number of object files in LINT that fail to compile
with -O2 but without the -fno-strict-aliasing kludge:
- amd64: 29 (down from 211)
- i386: 36 (down from 47)
gcc-3.4.6 actually allows the invalid constraints that result from not
using the temp. variable, at least with -O[1-2], but gcc-3.3.3 crashes
on them and I don't want to depend on compiler bugs.
register takes 16 characters (64-bit register in hex). In practice this
is a slight bit of overkill as 7 of the 56 registers are only 32-bit, but
having the buffer too small results in remote kgdb trashing kernel memory
when it connects.
PR: amd64/108673
Submitted by: Ravi Murty, Nikhil Rao @ Intel
MFC after: 3 days
the space allocated for the double fault handler since this space
is otherwise unused till the time a double fault occurs.
This change should have been committed alongside r1.127 of
"exception.S", but I somehow missed doing so.
Problem reported by: jeff
Pointy hat to: jkoshy
setrunqueue() was mostly empty. The few asserts and thread state
setting were moved to the individual schedulers. sched_add() was
chosen to displace it for naming consistency reasons.
- Remove adjustrunqueue, it was 4 lines of code that was ifdef'd to be
different on all three schedulers where it was only called in one place
each.
- Remove the long ifdef'd out remrunqueue code.
- Remove the now redundant ts_state. Inspect the thread state directly.
- Don't set TSF_* flags from kern_switch.c, we were only doing this to
support a feature in one scheduler.
- Change sched_choose() to return a thread rather than a td_sched. Also,
rely on the schedulers to return the idlethread. This simplifies the
logic in choosethread(). Aside from the run queue links kern_switch.c
mostly does not care about the contents of td_sched.
Discussed with: julian
- Move the idle thread loop into the per scheduler area. ULE wants to
do something different from the other schedulers.
Suggested by: jhb
Tested on: x86/amd64 sched_{4BSD, ULE, CORE}.
used by clock code, so don't export it to the world for machdep.c to
initialize. There is a minor problem initializing it before it is
used, since although clock initialization is split up so that parts
of it can be done early, the first part was never done early enough
to actually work. Split it up a bit more and do the first part as
late as possible to document the necessary order. The functions that
implement the split are still bogusly exported.
Cleaned up initialization of the i8254 clock hardware using the new
split. Actually initialize it early enough, and don't work around it
not being initialized in DELAY() when DELAY() is called early for
initialization of some console drivers.
This unfortunately moves a little more code before the early debugger
breakpoint so that it is harder to debug. The ordering of console and
related initialization is delicate because we want to do as little as
possible before the breakpoint, but must initialize a console.
- First off, device drivers really do need to know if they are allocating
MSI or MSI-X messages. MSI requires allocating powerof2() messages for
example where MSI-X does not. To address this, split out the MSI-X
support from pci_msi_count() and pci_alloc_msi() into new driver-visible
functions pci_msix_count() and pci_alloc_msix(). As a result,
pci_msi_count() now just returns a count of the max supported MSI
messages for the device, and pci_alloc_msi() only tries to allocate MSI
messages. To get a count of the max supported MSI-X messages, use
pci_msix_count(). To allocate MSI-X messages, use pci_alloc_msix().
pci_release_msi() still handles both MSI and MSI-X messages, however.
As a result of this change, drivers using the existing API will only
use MSI messages and will no longer try to use MSI-X messages.
- Because MSI-X allows for each message to have its own data and address
values (and thus does not require all of the messages to have their
MD vectors allocated as a group), some devices allow for "sparse" use
of MSI-X message slots. For example, if a device supports 8 messages
but the OS is only able to allocate 2 messages, the device may make the
best use of 2 IRQs if it enables the messages at slots 1 and 4 rather
than default of using the first N slots (or indicies) at 1 and 2. To
support this, add a new pci_remap_msix() function that a driver may call
after a successful pci_alloc_msix() (but before allocating any of the
SYS_RES_IRQ resources) to allow the allocated IRQ resources to be
assigned to different message indices. For example, from the earlier
example, after pci_alloc_msix() returned a value of 2, the driver would
call pci_remap_msix() passing in array of integers { 1, 4 } as the
new message indices to use. The rid's for the SYS_RES_IRQ resources
will always match the message indices. Thus, after the call to
pci_remap_msix() the driver would be able to access the first message
in slot 1 at SYS_RES_IRQ rid 1, and the second message at slot 4 at
SYS_RES_IRQ rid 4. Note that the message slots/indices are 1-based
rather than 0-based so that they will always correspond to the rid
values (SYS_RES_IRQ rid 0 is reserved for the legacy INTx interrupt).
To support this API, a new PCIB_REMAP_MSIX() method was added to the
pcib interface to change the message index for a single IRQ.
Tested by: scottl
Dont expose em->shared to the outside world before its properly
initialized. Might not affect anything but its at least a better
coding style.
Dont expose em via p->p_emuldata until its properly initialized.
This also enables us to get rid of some locking and simplify the
code because we are workin on a local copy.
In linux_fork and linux_vfork create the process in stopped state
to be sure that the new process runs with fully initialized emuldata
structure [1]. Also fix the vfork (both in linux_clone and linux_vfork)
race that could result in never woken up process [2].
Reported by: Scot Hetzel [1]
Suggested by: jhb [2]
Reviewed by: jhb (at least some important parts)
Submitted by: rdivacky
Tested by: Scot Hetzel (on amd64)
Change 2 comments (in the new code) to comply to style(9).
Suggested by: jhb
