from r202992. The refcount on the cache entry is not initialized, so
any attempt to clean the cache will skip over this item since it likely
has a >0 value.
This change is currently a NOP. There is work in progress to support
freeing the cache which requires this change to avoid a memory leak.
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Division
unmount, which causes error from nmount(2) call when performing
MNT_DELEXPORT over the directory which ceased to be a mount point.
The race is legitimate and innocent, but results in the chatty mountd.
Silence it by providing an distinguished error code for the situation,
and ignoring the error in mountd loop.
Based on the patch by: Andreas Longwitz <longwitz@incore.de>
Prodded and tested by: bdrewery
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Switch the cache line size during invalidations/flushes
to be read from CP15 cache type register.
Submitted by: Wojciech Macek <wma@semihalf.com>
Reviewed by: ian, imp
Obtained from: Semihalf
r272959 broke compatibility with mfsBSD that stores the default network
config file in /etc/rc.conf.d/network. In order to fix that load the network
config file from netif also.
endpoint less frequently to make the sample rate adjustment more
accurate. This should resolve problems with the DN32-USB module for
Midas audio systems and possibly other similar products from Klark
Teknik.
MFC after: 3 days
defaulting VMCONFIG to /dev/null, and additionally
ensuring VMCONFIG is not a character device before it
is sourced.
While here, be sure to exit if usage() is called.
This should effectively be no-op, but the usage() output
was discovered while investigating a larger issue.
MFC after: 1 week
X-MFC-with: r277458, r277536, r277606, r277609,
r277836, r278118, r278119, r278206
Sponsored by: The FreeBSD Foundation
This port failed to gain traction and probably only a couple Wii consoles
ran FreeBSD all the way to single user mode with an md(4). IPC
support was never implemented, so it was impossible to use any peripheral
Any further development, if any, will happen at https://github.com/rpaulo/wii.
Discussed with: nathanw (a long time ago), jhibbits
This change implements a notification (via devctl) to userland when
the kernel produces coredumps after a process has crashed.
devd can then run a specific command to produce a human readable crash
report. The command is most usually a helper that runs gdb/lldb
commands on the file/coredump pair. It's possible to use this
functionality for implementing automatic generation of crash reports.
devd(8) will be notified of the full path of the binary that crashed and
the full path of the coredump file.
hw.x2apic_enable tunable allows disabling it from the loader prompt.
To closely repeat effects of the uncached memory ops when accessing
registers in the xAPIC mode, the x2APIC writes to MSRs are preceeded
by mfence, except for the EOI notifications. This is probably too
strict, only ICR writes to send IPI require serialization to ensure
that other CPUs see the previous actions when IPI is delivered. This
may be changed later.
In vmm justreturn IPI handler, call doreti_iret instead of doing iretd
inline, to handle corner conditions.
Note that the patch only switches LAPICs into x2APIC mode. It does not
enables FreeBSD to support > 255 CPUs, which requires parsing x2APIC
MADT entries and doing interrupts remapping, but is the required step
on the way.
Reviewed by: neel
Tested by: pho (real hardware), neel (on bhyve)
Discussed with: jhb, grehan
Sponsored by: The FreeBSD Foundation
MFC after: 2 months
and arp were being used. They basically would pass in the
mutex to the callout_init. Because they used this method
to the callout system, it was possible to "stop" the callout.
When flushing the table and you stopped the running callout, the
callout_stop code would return 1 indicating that it was going
to stop the callout (that was about to run on the callout_wheel blocked
by the function calling the stop). Now when 1 was returned, it would
lower the reference count one extra time for the stopped timer, then
a few lines later delete the memory. Of course the callout_wheel was
stuck in the lock code and would then crash since it was accessing
freed memory. By using callout_init(c, 1) we always get a 0 back
and the reference counting bug does not rear its head. We do have
to make a few adjustments to the callouts themselves though to make
sure it does the proper thing if rescheduled as well as gets the lock.
Commented upon by hiren and sbruno
See Phabricator D1777 for more details.
Commented upon by hiren and sbruno
Reviewed by: adrian, jhb and bz
Sponsored by: Netflix Inc.
